Toshiba GD-1190 Service Manual Download Page 57

Page: 57 / 70

GD-1190 TROUBLE CODES 5 - 3

EOL

- (End Of Line) - This is the code sequence marking the end of a

line. It consists of eleven zeros followed by a one -
000000000001.

EOM

- (End Of Message) - Used in G II Phase D. Replaced with EOP

in G III.

EOP

- (End Of Procedure) - A signal issued by the transmitter indicat-

ing the end of a transmission.

FIF

(Facsimile Information Field) - The coded information that is
sent through the field (telephone line) when transmitting and
receiving.

FTT

- (Failure To Train) - A signal issued by the receiver indicating

that excessive noise on the phone line, and requesting retrain-
ing.

MCF

- (Message Confirmation) - A signal issued by the receiver indi-

cating all data has been received successfully.

MPS

- (Multi Page Signal) - Issued by the transmitter after the a page

of information was sent indicating another page is to follow.

MTT

- (Max. TX Time) - This is the maximum transmission time per

line.

NSF

- (Non Standard Facilities) - This signal is issued by the receiver

which contains specific manufacturers information relating to
procedures and specifications not covered in the CCITT/ITU
standards.

NSS

- (Non Standard Set Up) - An optional set up command issued by

the transmitter identifying itself and the transmission character-
istics determined by the information.

PIN

- (Procedure Interrupt Negative) - Indicates that the previous (or

in process message) message has not been satisfactorily
received and that further transmissions are not possible without
operator intervention.

PIP

- (Procedure Interrupt Positive) - Indicates the previous (or in pro-

cess) message has been received but that further transmission
are not possible with out operator intervention.

PIS

- (Procedure Interrupt Signal) - Issued by either the transmitter of

the receiver indicating termination of operation.

RTN

- (Retrain Negative) - Issued by the receiver indicating there is

noise on the phone line and to retrain.

RTP

- (Retrain Positive) - Issued by the receiver indicating no noise on

the phone line. However, the machine will need to retrain
because the user has made a change on the operation panel.

TCF

- (Training Check Field) - Test lasting 1.5 seconds, which con-

taining a series of ones (binary bit 1), issued by the transmitter
checking the quality of the phone line. If the test fails the trans-
mitter will try again at a slower speed.

TSI

(Transmitting Subscriber Identification) - An optional signal from
the transmitter containing its identification number (fax number).

05_TROUBLE CODES.fm 3

ページ

２００４年１２月２３日　木曜日　午後２時２３分

Summary of Contents for GD-1190







































































Search results

Summary of Contents for GD-1190

Reviews:

Related manuals for GD-1190

Brands by name

Popular brands

Toshiba GD-1190, Service Manual

Search results

Summary of Contents for GD-1190

Reviews:

Related manuals for GD-1190

Brands by name

Popular brands