Toshiba GD-1190 Service Manual Download

Page: 10 / 70

GD-1190 SPECIFICATIONS 1 - 5

Memory
functions
system

Memory outline

Memory capacity

Standard memory

2MB

Option

Document quantity to
be stored

A4 standard documents 120 pages

Data storage area/
backup when service
interruption (Recorded
data, receive data)

Image data

Flash memory (Data are retained when the power is
turned off or when the battery is exhausted.)

Data other than image

SRAM (Data are retained when the power is turned
off, but deleted when the battery is exhausted with
the power OFF.)

Treatment when
memory full

Quick online

Memory full on the first
page

Send cancel without call-out

Memory full on the
second or later page

The line is shut-off after sending the last page of
scanned data.

Memory send

Memory full on the first
page

Send cancel

Memory full on the
second or later page

Send/Cancel is selected depending on the select
menu display.
Send: The line is shut off after sending the scanned
data.
Cancel: Cancel even scanned data.

Memory status check
function

Yes (The remaining memory capacity (%) is
displayed on the LCD.)

Memory content check
function

Not-sent job is displayed on the LCD. (Cancel is
possible.)

Document jam

Error LED, LCD message are displayed.

Service
functions
system

Test command
function

Send/receive of specified signals, commands, and
image data are performed without a remote machine.

Counter function

Communication
counter

• Number of send pages
• Number of receive pages
• Number of output pages
• Send time
• Receive time

Others

Environmental
functions

Auto clear

Conforms to the main unit setting. When the
operation is left for 1 min or more, the display returns
to the main menu.

Auto shut -off

Conforms to the main unit setting.

Date and time setting
function

Month/ Day/ Year/ Day of week/ O'clock/ minute

Image priority function

STANDARD/FINE/SUPER FINE

BEEP LENGTH
(Communication end
sound length) setting

3SEC/1SEC/NO BEEP

Auto summer time
setting

First Sunday of April AM2:00

→

3:00,

Last Sunday of October AM2:00

→

1:00

(Default: OFF)

Multi language
function

Conforms to the main unit setting.

Large item

Middle item

Small item

Sub item

Specifications

ARFX9̲A1E.book 5 ページ２００４年１２月３日金曜日午後４時２２分

Summary of Contents for GD-1190







































































Search results

Summary of Contents for GD-1190

Reviews:

Related manuals for GD-1190

Brands by name

Popular brands

Toshiba GD-1190, Service Manual

Search results

Summary of Contents for GD-1190

Reviews:

Related manuals for GD-1190

Brands by name

Popular brands