Toshiba D-VR16SB, Owner'S Manual

Page: 55 / 73

55 EN
Recording
Playback
Editing
Introduction
Connections
Basic Setup
Function Setup
Others
VCR Functions
Hints for Timer Recording
● If there is a power failure or the unit is unplugged for
more than 30 seconds, the clock setting and all timer
settings will be lost.
● If there is no disc or an unrecordable disc in the tray,
the icon will flash and timer recording will not occur.
Insert a recordable disc.
● If there is no tape or a tape with a record tab is not in
the cassette compartment, VCR flashes in the front
panel display and timer recording cannot be
performed. Please insert a recordable tape.
● When all timer recordings are complete, the icon
flashes. To play back or eject the recorded disc, press
[T-SET], and then press [PLAY
B
] or
[OPEN/CLOSE
A
].
● The timer recording cannot be performed in DVD and
VCR at the same time. If you set two programmings
with the same channel and time both in DVD and VCR,
the programming that has priority will be recorded.
●
You cannot make any DVD operation during DVD
timer recording.
● You cannot make any VCR operation during VCR
timer recording.
● If the Start and End times are the same, the length of
the recording will be set for 24 hours. If the disc
becomes full during recording, the unit will turn itself
off. To continue recording, press [T-SET] to cancel the
timer-standby mode, insert a recordable disc and press
[T-SET] again.
●
If two or more programmes overlap, “Overlap” and the
overlapped programme number will appear on the
display.
●
If the Start time is earlier and the End time is later than
the current time, the recording will start immediately
after you press [T-SET].
●
If a videotape ends during timer recording, the unit will
automatically stop, eject the videotape, and turn itself
off. To continue recording, insert a recordable tape.
●
If you turn on the unit in the timer-standby mode, only
the component (DVD or VCR) which is not currently
timer-programmed can be operated.
The unit will return to the timer-standby mode when
the power is turned off.
■ The priority of overlapped settings
The unit records programmes according to priority if
the timer programmes overlap.
■ If the starting time is same:
• The timer programming set first (PROG. 1) has
priority.
PROG. 1
PROG. 2
Actual
recording
PROG. 1 PROG. 2
PROG. 2
recording
will start
after
PROG. 1
recording is
completed.
The first 30 seconds (approx.) are cut off.
■ If the recording time is partially overlapped:
• The timer programming with the earlier start time
(PROG. 2) has priority. PROG. 1 will start after
PROG. 2 recording is complete.
■ If the recording time entirely overlaps:
• The shorter timer programming (PROG. 1) is not
recorded.
■ If the End time of the programme currently
being recorded and the Start time of the
subsequent programme are same:
• If PROG. 1 is a DVD recorded programme, the
beginning of PROG. 2 may be cut off.
PROG. 1
PROG. 2
Actual
recording
PROG. 1 PROG. 2
The first 30 seconds (approx.) are cut off.*
■ Note for DVD recording
• If the recording time of two programmes overlap, or the
End time of a programme and the Start time of another is
same, the first 30 seconds (approx.) of the subsequent
programme are cut off.
PROG. 1
PROG. 2
Actual
recording
PROG. 2 PROG. 1
The first 30 seconds (approx.) are cut off.
PROG. 1
PROG. 2
Actual
recording
PROG. 2
* If the cut off time exceeds 1 minute, the error number
“E40” will appear in the Timer Programming list.
■
If programming has been made at the end of
the programming (PROG. 1) currently being
recorded:
• The timer programming set first (PROG. 2) has
priority. PROG. 3 will not be recorded.
PROG. 1
PROG. 2
PROG. 3
Actual
recording
PROG. 1 PROG. 2
PROG. 2
recording
will start
after
PROG. 1
recording is
completed.
The first 30 seconds (approx.) are cut off.
05̲Recording̲BD.indd 55 05̲Recording̲BD.indd 55 2006/03/24 14:37:46 2006/03/24 14:37:46