manualshive.com logo in svg

Toshiba D-VR16SB, Owner'S Manual

Share
Download
Toshiba D-VR16SB Owner'S Manual Download Page 21

Introduction

21

EN

Recording

Playback

Editing

Introduction

Connections

Basic Setup

Function Setup

Others

VCR Functions

Installing batteries in the remote 
control

About the remote control

Preparation of the remote control

■ 

Install two R6 (AA) batteries (supplied) into the 

remote control, carefully match with the 

polarity indicated inside the battery 

compartment.

1

Open the cover.

2

 Insert batteries.

Make sure to match the + and - on the 
batteries to the marks inside the battery 
compartment.

3

  Close the cover.

■ 

Keep in mind the following when using the 

remote control:

● 

Make sure there is no obstacle between the remote 

control and the remote control sensor on the unit.

● 

Use within the operating range and angle as 

shown.

● 

Remote control operation may become unreliable if 

the remote control sensor of the unit is being 

exposed by the strong sunlight or fluorescent light.

● 

Remote controls for different devices can interfere 

with each other. Be careful when using remote 

controls for other equipment located close to the 

unit.

● 

Replace the batteries when the operating range of 

the remote control reduces.

● 

The maximum operable range as follows:

 -  

Line of sight

: 

  approximately 7 m
 -  

Either side of the centre

: 

  approximately 7 m within 30 degrees

ON / STANDBY

VCR

REC

DUBBING

PROGRAM

VCR/DVD

REC

DVD

DVD

VCR

Notes:

• Incorrect use of batteries can result in hazards such as 

leakage and bursting.

• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
• Make sure that the + and - ends of each battery match the 

indications inside the battery compartment.

• Remove batteries if the remote control will not be used for 

an extended period of time.

• When disposing used batteries, please comply with 

governmental regulations or the public instructions for 

environmental protection that apply in your country or 

area.

• Do not recharge, short-circuit, heat, burn or disassemble 

batteries.

02̲Introduction̲BD.indd   21

02̲Introduction̲BD.indd   21

2006/03/24   14:35:51

2006/03/24   14:35:51

Summary of Contents for D-VR16SB










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands