background image

Workman HDX--D

Page 4 -- 11

Briggs/Daihatsu Diesel Engine

Removal (Fig. 8)

1. Park vehicle on a level surface and engage parking

brake. Stop the engine and remove key from ignition

switch. Allow engine to cool.

2. Raise or remove the bed or other attachment(s). If

bed is raised, place safety support on lift cylinder.

3. Remove exhaust system components as needed us-

ing Figure 8 as a guide.

4. Discard gaskets and thoroughly clean flange sur-

faces of exhaust tube and muffler.

Installation (Fig. 8)

1. Replace any removed gaskets.

2. Using Figure 8 as a guide, fit all exhaust components

to vehicle before tightening any fasteners. When secur-

ing exhaust, tighten fasteners in the following order:

A. Hex nuts (item 4) that secure exhaust tube to en-

gine.

B. Flange head screw (item 11) that secures muffler

to transaxle.

C. Flange head screws (item 14) and flange nuts

(item 8) that secure muffler to exhaust tube.

D. Flange head screws (item 6) and flange nuts

(item 8) that secure muffler to shift cable mount

bracket.

E. Carriage bolts (item 13) and flange nuts (item 8)

that secure muffler to mount plate.

3. Lower or install bed or attachment(s).

Briggs

/Da

iha

ts

u

Diesel

En

g

in

e

Summary of Contents for Workman HD Series































































































































































































































































































































Reviews: