!
I
!! '5%'/)( *380)( (-57; 35 37,)5:-6)
1%0*82'7-32-2+ 64%5/ 408+ 1867 &) 5)40%')( 3
237 6%2( &0%67 6'5%4) 35 '0)%2 )0)'753()6 &; 86-2+
% :-5) &586, &)'%86) +5-7 1%; )9)278%00; 5)0)%6)
*531 7,) 408+ %2( *%00 -273 7,) ';0-2()5 !,) 5)6807 -6
868%00; % (%1%+)( )2+-2)
Set air gap between center and side of electrodes
at 0.030". Install correctly gapped spark plug w/gasket
seal, and tighten plug to 200 in-lb. If torque wrench is
not used, tighten plug firmly.
$
To avoid overheating and possible engine damage,
cooling fins on cylinder head must be kept clean.
$" $ !
!
-+
The hydraulic system filter must be changed initially,
after the first 8 hours of operation, and thereafter every
400 hours of operation or yearly, whichever comes first.
Use a genuine Toro oil filter for replacement. The
hydraulic oil must be changed every 400 hours of
operation or yearly, whichever comes first.
Park the machine on a level surface and turn the
engine off.
Pivot seat upward.
Disconnect tube from bottom fitting of reservoir
and let oil flow into drain pan. Reinstall and tighten tube
when oil stops draining.
Clean the area around the hydraulic oil filter.
Remove filter from the bottom of the filter housing and
allow the oil to flow into a drain pan. Use bottom type
filter wrench. Dispose of the oil filter properly.
-+85)
;(5%80-' *-07)5
Apply a film of oil on the filter gasket. Install filter by
hand until gasket contacts mounting head; then
tighten filter an additional three-fourths turn.
Fill the reservoir to proper level, refer to Check
Hydraulic System, page 11
Place all controls in neutral or disengaged position
and start engine. Run engine at lowest possible RPM to
purge the system of air.
Run engine until lift cylinder extends and retracts
and forward and reverse wheel motion is achieved.
Stop the engine and check the oil level in reservoir,
add oil if necessary.
Check all connections for leaks.
Lower seat.
Dispose of oil properly.
$"
Check hydraulic lines and hoses daily for leaks, kinked
lines, loose mounting supports, wear, loose fittings,
weather deterioration and chemical deterioration.
Make all necessary repairs before operating.
#
))4 &3(; %2( ,%2(6 %:%; *531 4-2 ,30)
0)%/6 35 23<<0)6 7,%7 ).)'7 ,-+, 45)6685) ,;=
(5%80-' *08-( "6) '%5(&3%5( 35 4%4)5 73 *-2(
,;(5%80-' 0)%/6 ;(5%80-' *08-( )6'%4-2+ 82=
()5 45)6685) '%2 4)2)75%7) 6/-2 %2( '%86) -2=
.85; 08-( %''-()27%00; -2.)'7)( -273 7,) 6/-2
1867 &) 685+-'%00; 5)139)( :-7,-2 % *):
,3856 &; % (3'735 *%1-0-%5 :-7, 7,-6 *351 3* -2=
.85; 35 +%2+5)2) 1%; 5)6807
$" $ !
-+
Whenever a hydraulic component is repaired or
replaced hydraulic oil filter should be changed and
hydraulic system charged.
!! %/) 685) ,;(5%80-' 5)6)593-5 %2(
*-07)5 %5) *-00)( :-7, 3-0 %7 %00 7-1)6 :,)2 ',%5+-2+
,;(5%80-' 6;67)1
Park the machine on a level surface and turn the
engine off.
Pivot seat upward and remove engine shield.
Loosen lock nut on spring adjusting pin until
bearing moves freely from cam on lever, allowing pump
shaft freedom to rotate during start-up.
Summary of Contents for Sand Pro 3020
Page 26: ... ...
