manualshive.com logo in svg

Toro 68021HD, Operator'S Manual

Share
Download
Toro 68021HD Operator'S Manual Download Page 37

E.

If needed, pivot the engine on the engine deck
until the engine pulley and the idler pulley are
aligned to the straightedge (

Figure 57

).

F.

Tighten the nuts and bolts that secure the engine
to the engine deck to a torque of 18 N∙m (13 ft-lb).

G.

Check the air gap between the engine deck and
the roller on the clutch. If the air gap is not within
the specified range, repeat step

3

until the air gap

measurement is within the specified range.

H.

Install the divider plate; refer to

Installing the

Divider Plate (page 27)

.

Replacing the
Belts—Belt-drive Models

Service Interval:

Every 2 years—Replace the belts.

Removing the Belts

1.

Move the clutch lever to the O

FF

position.

2.

Remove the divider plate; refer to

Removing the

Divider Plate (page 27)

.

3.

Remove the bolt that secures the belt guide to the
engine and remove the belt guide (

Figure 58

).

1

2

G020010

Figure 58

1.

Bolt

2.

Belt guide

4.

Slip the forward belt forward and off the idler pulley
(

Figure 59

).

2

3

4

1

G020012

Figure 59

1.

Engine pulley

3.

Idler pulley

2.

Forward belt

4.

Rear belt

5.

Slip the rear belt rearward and off the idler pulley
(

Figure 59

).

6.

Slip the belts off the engine pulley.

7.

Remove the belts from the machine.

Installing the Belts

1.

Ensure that the clutch lever is in the O

FF

position.

2.

Align the rear belt to the rear groove in the engine
pulley.

Note:

Do not align the rear belt to the idler pulley.

3.

Align the forward belt to the forward groove of the
idler pulley.

4.

Slip the rear belt over the idler pulley and align the belt
to the rear pulley groove.

5.

Slip the forward belt over the engine pulley and align
the belt to the forward pulley groove.

6.

Check the belt tension; refer to step

1

, step

2

, and step

3

in

Adjusting the Belt Tension (page 36)

.

7.

Loosely secure the belt guide to the engine (

Figure 58

)

with the bolt that was removed in step

3

of

Removing

the Belts (page 37)

.

8.

Adjust the belt guide; refer to

Adjusting the Belt Guide

(page 38)

.

9.

Install the divider plate; refer to

Installing the Divider

Plate (page 27)

.

37

 

Summary of Contents for 68021HD













































Reviews:

No comments

Brands by name

Popular brands

Load more brands