manualshive.com logo in svg

Toro 68021HD, Operator'S Manual

Share
Download
Toro 68021HD Operator'S Manual Download Page 16

Hitching a Machine with a Pintle Hitch
Coupler

1.

Hitch the machine as shown in

Figure 18

.

Figure 18

2.

If the machine is equipped with a trailer-light kit,
connect the wire plug of the tow vehicle to the wire
plug of the machine.

Connecting the Safety Chains to the
Tow Vehicle

1.

Pull the safety chain through the slots in the keyholes,
so that the lengths on each side are equal.

2.

Cross both lengths of chain

under

the tow pole.

Note:

Crossing the chains decreases the chances of

the front of the machine dropping to the ground if the
hitch does not hold the connection.

1

2

3

G021 177

Figure 19

1.

Connecting links

3.

Chain crossed under tow
pole

2.

Keyholes in front post

3.

Connect each length of chain to the safety chain
mounting point on the tow vehicle with the connecting
links (

Figure 20

).

Important:

Ensure that the chain has enough

slack for turning around corners when towing the
machine.

Note:

Stow the excess chain inside the bottom of the

front post by pushing it into the keyholes and latching
the appropriate links into the keyhole slots.

16

 

Summary of Contents for 68021HD













































Reviews:

No comments

Brands by name

Popular brands

Load more brands