manualshive.com logo in svg

Toro 68021HD, Operator'S Manual

Share
Download
Toro 68021HD Operator'S Manual Download Page 15

Hitching a Machine with a Stamped Ball
Coupler

1.

Apply chassis grease to the socket of the coupler and
the area of the clamp that contacts the ball.

2.

Oil the pivot points and sliding surfaces of the coupler
with SAE 30 motor oil.

3.

Hitch the machine as shown in

Figure 16

.

Figure 16

4.

If the machine is equipped with a trailer-light kit,
connect the wire plug of the tow vehicle to the wire
plug of the machine.

Hitching a Machine with a Forged Ball
Coupler

1.

Apply removable thread-locking compound to the
threads of the coupler bolt to prevent the coupler
handle from coming loose.

Important:

Apply thread-locking compound as

needed in the future.

2.

Apply chassis grease to the socket of the coupler and
the area of the clamp that contacts the ball.

3.

Install hitch the machine as shown in

Figure 17

.

Figure 17

Note:

Use a wrench to keep the bolt from spinning.

4.

If the machine is equipped with a trailer-light kit,
connect the wire plug of the tow vehicle to the wire
plug of the machine.

15

 

Summary of Contents for 68021HD













































Reviews:

No comments

Brands by name

Popular brands

Load more brands