manualshive.com logo in svg

Toro 68021HD, Operator'S Manual

Share
Download
Toro 68021HD Operator'S Manual Download Page 26

Maintenance

Important:

Before performing any maintenance procedures, first shut off the engine, wait 5 minutes to allow all

moving parts to come to a complete stop and cool, and disconnect the spark-plug wire.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 25 hours

• Change the engine oil.
• Inspect the belts and adjust as necessary.

Before each use or daily

• Inspect the tires and wheels.
• Inspect the air-cleaner elements.
• Check the engine-oil level.

After each use

• Torque the lug nuts to 108 to 122 N∙m (80 to 90 ft-lb) after towing.
• Clean the drum between mixing batches of material.
• Lubricate the trunnions.

Every 40 hours

• Inspect the belts and adjust as necessary.
• Check the clutch operation

Every 50 hours

• Clean the air-cleaner elements. Clean them more frequently in dusty operating

conditions.

Every 100 hours

• Change the engine oil.
• Check the spark plug.
• Clean the spark arrester.
• Clean the fuel-sediment cup.

Every 300 hours

• Replace the paper air-cleaner element. Replace it more frequently in dusty

operating conditions.

• Replace the spark plug.

Monthly

• Lubricate the pillow-block bearings.

Yearly or before storage

• Clean the fuel-sediment cup.

Every 2 years

• Replace the belts.

Important:

Refer to your engine owner’s manual for additional maintenance procedures.

26

 

Summary of Contents for 68021HD













































Reviews:

No comments

Brands by name

Popular brands

Load more brands