manualshive.com logo in svg

Toro 68021HD, Operator'S Manual

Share
Download
Toro 68021HD Operator'S Manual Download Page 32

Figure 44

1.

Spark plug

2.

Wire

4.

Clean around the spark plug.

5.

Rotate the spark plug counterclockwise using a 21 mm
(13/16 inch) spark-plug wrench to remove the plug
and the sealing washer (

Figure 45

).

G019749

Figure 45

Checking the Spark Plug

Important:

Do not clean the spark plug. Always replace

the spark plug when it has: a black coating, worn
electrodes, and oily film, or cracks.

Note:

If you see light brown or gray on the insulator, the

engine is operating properly. A black coating on the insulator
usually means that the air cleaner is dirty.

Set the gap to 0.7 to 0.8 mm (0.028 to 0.031 inch).

B

A

g027479

Figure 46

Installing the Spark Plug

Important:

Ensure that the gap between the side and

center electrodes is correct before installing the spark
plug.

1.

Thread the spark plug clockwise into the spark-plug
hole by hand.

Note:

Avoid cross-threading the spark plug with the

threads of the spark-plug hole.

2.

Rotate the spark plug clockwise using a 21 mm (13/16
inch) spark-plug wrench until the plug and sealing
washer are seated (

Figure 45

).

3.

Tighten the spark plug as follows:

•

When installing an

in-service

spark plug, tighten

the plug an additional 1/8 to 1/4 turn.

•

When installing a

new

spark plug, tighten the plug

an additional 1/2 turn.

4.

Push the spark-plug wire onto the terminal of the spark
plug (

Figure 44

).

32

 

Summary of Contents for 68021HD













































Reviews:

No comments

Brands by name

Popular brands

Load more brands