Toro 30799 Operator'S Manual Download Page 17

17

Maintenance

Greasing The Cutting Unit

The cutting unit must be lubricated regularly. If machine is
operated under normal conditions, lubricate castor bearings
and bushings with No. 2 general purpose lithium base
grease or molybdenum base grease, after every 8 hours of
operation or daily, whichever comes first.

1. The cutting unit has bearings and bushings that must be

lubricated, and these lubrication points are: front castor
spindle bushings (2) (Fig. 26); front castor wheel
bearings (4) (Fig. 26); rear castor wheel bearings (2)
(Fig. 28); blade spindle bearings (3) (Fig. 28); right and
left push arm ball joints (Fig. 28); drive shaft (3)
(Fig. 28) idler arm pivots (3) (Fig. 29); and deck pivot
pins (4) (Fig. 30)

Figure 26

Figure 27

Figure 28

Figure 29

Figure 30

2. Position the machine on a level surface and lower

cutting unit. Remove fill/check plug from side of gear
box (Fig. 31) and make sure lubricant is up to bottom of
hole. If level of lubricant is low, add SAE 80–90 wt.
gear lube until level is up to bottom of hole.

2

1

Figure 31

1.

Fill/check plug

2.

Drain plug

Summary of Contents for 30799

























Reviews: