Toro 30799 Operator'S Manual Download Page 13

13

Before Operating

Check Lubricant In Gear Box

The gear box in designed to operate on SAE 80–90 wt. gear
lube. Although the gear box is shipped with lubricant from
the factory, check the level before operating the cutting
unit.

1. Position the machine and cutting unit on a level surface.

2. Remove check plug from side of gear box and make

sure lubricant is up to bottom of hole. If level of
lubricant is low, add enough lubricant to bring it up to
bottom of hole.

1

2

Figure 16

1.

Fill/check plug

2.

Drain plug

Adjusting Height-of-cut

The height-of-cut is adjustable from 1 to 4

 

inches in 1/4

inch increments.

1. Start the engine and raise the cutting unit so

height-of-cut can be changed. Stop engine after cutting
unit is raised.

Front Castor Wheels

Figure

 17

1. Remove H.O.C. cap from spindle shaft and slide spindle

out of front castor arm. Slide spacers onto spindle shaft
to get desired height-of-cut.

1

4

4

3

3

Figure 18

1.

Front castor wheel

2.

H.O.C. cap

3.

Spacer

4.

Washer

2. Push castor spindle through front castor arm install

remaining spacers onto spindle and install HOC cap to
secure assembly.

Summary of Contents for 30799

























Reviews: