Tormach pathpilot Installation Manual Download Page 7 | Manualshive

Page: 7 / 24

background image

MOUNT THE CONSOLE

13. Drill the remaining three holes for the mount arm's bottom bracket.

Figure 5: Drilling the remaining three holes into the enclosure.

14. Put three M5 × 0.8 - 10 screws and washers into the remaining three holes.

15. Once the mount arm is secured to the enclosure, open the enclosure door and verify that the mount arm's

screws don't interfere with the enclosure door jamb. If they do, loosen the screws on the door jamb, and
slide it toward the back of the machine.

Figure 6: Door jamb moved to provide clearance for the mount arm's screws.

MOUNT THE CONSOLE

Complete the following steps in the order listed:

Assemble the Controller and Keyboard Tray

Lift and Secure the Controller Assembly

Page 7

©Tormach® 2022
Specifications subject to change without notice.

tormach.com

TD10715: Installation Guide: PathPilot Operator Console for 770 (0822A)

«
...
5
6
7
8
9
...
»

Summary of Contents for pathpilot

























Reviews:

No comments

Related manuals for pathpilot

Brand: Rosewill Pages: 18

Brand: Conceptronic Pages: 90

Brand: Concept2 Pages: 4

Brand: BlueStork Pages: 60

Brand: American Dryer Pages: 2

Brand: Hamilton Pages: 12

Super-sonic 212

Brand: Fender Pages: 10

Brand: AirLive Pages: 91

Brand: Adata Pages: 15

Brand: Pulsar Pages: 2

Brand: Tripp Lite Pages: 2

Brand: Mustee Pages: 4

Brand: Leviton Pages: 30

Brand: 3M Pages: 17

Brand: 3M Pages: 28

Brand: 3M Pages: 32

ALUMAX 1040 Series

Brand: Sapa Pages: 8

Brand: OBERON Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands