Tormach pathpilot Installation Manual Download Page 9 | Manualshive

Page: 9 / 24

background image

MOUNT THE CONSOLE

5. Find the three provided mount arm brackets.

Figure 9: Mount arm brackets.

6. Loosely attach two of the mount arm brackets to the left side of the controller with four M4 × 0.7 - 10

screws using a 2.5 mm hex wrench, as shown in the following image. Verify that the curved edge is facing
away from the controller.

Note:

Don't completely tighten the brackets to the controller. You'll adjust them when you're

adjusting the height of the entire console assembly.

Figure 10: Two mount brackets attached to the controller.

Page 9

©Tormach® 2022
Specifications subject to change without notice.

tormach.com

TD10715: Installation Guide: PathPilot Operator Console for 770 (0822A)

«
...
7
8
9
10
11
...
»

Summary of Contents for pathpilot

























Reviews:

No comments

Related manuals for pathpilot

Brand: Vantec Pages: 26

Brand: BlueStork Pages: 68

Brand: ADC Pages: 56

Brand: Compaq Pages: 32

Brand: multicomp pro Pages: 2

Brand: urmet domus Pages: 8

Brand: BIOS AP Pages: 2

Brand: Conteg Pages: 40

Brand: Ewent Pages: 8

Brand: Red4Power Pages: 28

Brand: Center Pages: 11

Brand: REGALUX Pages: 28

Brand: Avastor Pages: 19

Core X9 - A-2014.11

Brand: Thermaltake Pages: 14

Brand: Rasilient Pages: 32

Brand: Quantum Pages: 16

Brand: Protective Enclosures Company Pages: 20

Brand: APLIC Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands