manualshive.com logo in svg

TOPMAQ WWBA1650 Series, Operator'S Manual, Page: 10 / 16

Share
Download
TOPMAQ WWBA1650 Series Operator'S Manual Download Page 10

 

10 

5.  Fix the band saw to a workbench by using four thread forming screws (not provide). 

Place the fence and miter gauge onto the table. 

 

 

 

 

 

     

 

 

 

 

 

 

 

 

 

ADJUSTING 

WARNING: Always be sure that the tool is switched off and unplugged before any adjustments. 

1. Tilting 

table 

 

Loosen the table lock handle slightly. 

 

Turn the angle adjustment knob, tilting the saw table until it reaches the desired angle. 

 

Using the scale indicator, check angle markings. 

 

Retighten the table lock knob to hold saw table securely in place. 

   

 

. 

 

 

 

 

 

 

 

 

 

 

 

 

2. 

Aligning the saw blade

_ 

If the saw blade does not run in the center of the rubber tyre, the tracking needs to be corrected by adjusting the tilt of the 

upper band saw wheel. 

Open the upper and lower cover. Manually rotate the upper wheel, taking care no to touch the blade. 

Turn tracking set knob clockwise or anticlockwise until the saw blade tracks centered on the rubber tyre. 

Thread forming 

screw 

Table locking handle 

Miter gauge 

Angle adjustment knob

Fence 

Thread forming 

screw 

Summary of Contents for WWBA1650 Series

















Reviews:

No comments