Topex TOPEX MobiLink IP User Manual Download Page 33 | Manualshive

Page: 33 / 80

background image

TOPEX MobiLink

IP

Preliminary Manual

Status

Each configuration submenu begins with a “Status” page that shows the current state for the
respective group of parameters.
It this case, it shows info about the state of the Ethernet interface and the current static routes:

Network Interface

This is the detailed information about the Ethernet network interface of the MobiLinkIP. It contains two
similar groups of network parameters:

Adm0

Details about the real Ethernet interface, including MAC (physical address), Internet address (logical
address), Broadcast, subnet mask, MTU value, metric, statistics (packets, errors, collisions, mega
bytes transferred) for the reception (RX) and respectively transmission (RX).

lo

Local Loopback interface

TOPEX S.A. +4 021.408.39.00

http://www.topex.ro

Page 33 of 80

«
...
31
32
33
34
35
...
»

Summary of Contents for TOPEX MobiLink IP

















































































Reviews:

No comments

Related manuals for TOPEX MobiLink IP

Brand: D-Link Pages: 10

Brand: D-Link Pages: 17

Brand: ICC Pages: 281

Anybus Communicator CAN PROFINET IRT 2.32

Brand: HMS Pages: 44

Brand: Epygi Pages: 55

Brand: IFM Pages: 131

Brand: Technica Engineering Pages: 7

Brand: Motorola Pages: 28

Brand: Motorola Pages: 351

SURFboard eXtreme SBG6782-AC

Brand: Motorola Pages: 2

Brand: Juniper Pages: 232

Brand: Juniper Pages: 394

Brand: Wildix Pages: 14

Brand: Telstra Pages: 100

Superlink SC-WBGW256

Brand: Mitsubishi Heavy Industries Pages: 44

Brand: Mitsubishi Heavy Industries Pages: 54

Brand: RTA Pages: 66

Unified Security Gateway

Brand: FaceTime Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands