background image

 

Safety Installation Information 

1.  READ and FOLLOW all instruction. 

2.  The gate opener is intended for use with Class I 

vehicular swing gates. 

Class  I  denotes  a  vehicular  gate  opener  (or  system) 

dwellings,  or  a  garage  or  parking  area  associated 

therewith. 

Install  the  gate  opener  only  when  the  opener  is 

appropriate for the construction and the usage class of 

the gate. 

3.  Gate  opening  system  designers,  installers  and 

users  must  take  into  account  the  possible  hazards 

associated with each individual application. Improperly 

designed, installed or maintained systems can create 

risks  for  the  user  as  well  as  the  bystander.  Gate 

system  design  and  installation  must  reduce  public 

exposure  to  potential  hazards.  All  exposed  pinch 

points must be eliminated or guarded. 

4.  A  gate  opener  can  create  high  levels  of  force 

during  normal  operation.  Therefore,  safety  features 

must  be  incorporated  into  every  installation.  Specific 

safety features include safety sensors. 

5.  The  gate  must  be  properly  installed  and  work 

freely  in  both  directions  prior  to  the installation  of  the 

gate opener. 

6.  The  gate  must  be  installed  in  a  location  so  that 

enough  clearance  is  provided  between  the  gate  and 

adjacent  structure  when  opening  and  closing  to 

reduce  the  risk  of  entrapment.  Swinging  gates  shall 

not open into public access areas. 

7.  The opener is intended for use only on gates used 

for  vehicles.  Pedestrians  must  be  supplied  with  a 

separate  access  opening.  The  pedestrian  access 

opening  shall  be  designed  to  promote  pedestrian 

usage.  The  pedestrian  access  shall  be  located  such 

that persons will not come in contact with the moving 

vehicular gate.

 

 

 

8.  Pedestrians should never cross the pathway of a 

moving  gate.  The  gate  opener  is  not  acceptable  for 

use  on  any  pedestrian  gate.  Pedestrians  must  be 

supplied with a separate pedestrian access. 

9.  For  an  installation  utilizing  non-contact  sensors 

(safety  sensors),  see  product  manual  on  the 

placement of non-contact sensors (safety sensors) for 

each type of application. 

a.  Care  shall  be  exercised  to  reduce  the  risk  of 

nuisance  tripping,  such  as  when  a  vehicle  trips  the 

safety sensor while the gate is still moving. 

b.  One or more non-contact sensors (safety sensors) 

shall  be  located  where  the  risk  of  entrapment  of 

obstruction exists, such as the perimeter reachable by 

a moving gate or barrier. 

10.  Never  mount  any  device  that  operates  the  gate 

opener where the user can reach over, under, around 

or  through  the  gate  to  operate  the  controls.  Controls 

are to be placed at least 6

’ (1.8m) from any part of the 

moving gate. 

 

11.  Controls intended to be used to reset an operator 

after  2  sequential  activations  of  the  entrapment 

protection  device  or  devices  must  be  located  in  the 

line  of  sight  of  the  gate,  or  easily  accessible  controls 

shall  have  a  security  feature  to  prevent  unauthorized 

use.  Never  allow  anyone to  hang  on  or  ride  the  gate 

during the entire travel of the gate. 

12.  Each  gate  opener  is  provided  with  two  safety 

warning placards. The placards are to be installed on 

the  front  and back  of  the gate  where  they  are  plainly 

visible. The placards may be mounted using cable ties 

through the four holes provided on each placard. 

All  warning  signs  and  placards  must  be  installed 

where visible in the area of the gate.

   

 

Summary of Contents for A3132




































Reviews: