Tomura DVR5216-A User Manual Download Page 82 | Manualshive

Page: 82 / 89

Tomura DVR5216-A User Manual Download Page 82

82

User Manual

When system is in standby or running state, if system was cut off power supply abnormally, after the power supply recovered, the system will auto-start up and recover to the working
state before power supply cut off. It can make the system work continuous when system may loss power supply.

To do Logout User, Shutdown, Restart operations by “Main Menu” ->
“Shutdown” menu as right picture:

Logout: Device will auto-lock after logout.
Shutdown: After you shutdown here, please click the power button in

front panel to start up DVR.

4.12 Password Reset

When user forget the DVR host administrator password, please recover password by following steps:
1. Shutdown DVR host. Cut off the power supply.
2. Remove the cover screws to open the case cover.
3. Find the J1 contact pin on top right of the back of front panel.
4. Set the 1, 2 pin of J1 contact pin to short-circuit by jumper block. (The jumper cap default in 2, 3 foot when leave factory).
5. Turn on the power to start the host, the front panel buzzer will beep, indicating that the password has been cleared to the factory defaults.
6. Shutdown the host and cut off power supply again.
7. Unplug the jumper block, set the 1, 2 pin of J1 contact pin to open-circuit, and place jumper block to J1 contact pin.
8. Fixed on the chassis cover, password reset is complete.

4.11 Logout/Shutdown/Reboot

4.13 Power Resume

«
...
80
81
82
83
84
...
»

Summary of Contents for DVR5216-A


























































































Reviews:

No comments