Doc# 16302
Press Pilot 150 Manual
Page 34
_
Message Code 4 & 104 – TIE DOWN STN-3 RELEASE BUTTONS
A tie-down fault has occurred at station 3. Check to make sure the
run buttons are released. If the buttons are released, check to make
sure the correct contacts are being used on the corresponding
inputs.
Note: The left and right run buttons of any station being used must
include a NO and a NC contact. These contacts must be wired into the
PP150 correctly, and must change state when depressed.
Message Code 5 & 105 – TIE DOWN STN-4 RELEASE BUTTONS
A tie-down fault has occurred at station 4. Check to make sure the
run buttons are released. If the buttons are released, check to make
sure the correct contacts are being used on the corresponding
inputs.
Note: The left and right run buttons of any station being used must
include a NO and a NC contact. These contacts must be wired into the
PP150 correctly, and must change state when depressed.
Message Code 6 & 106 – MULTIRUN TIMEOUT RELEASE BUTTONS
This message occurs when multiple stations are active and all active
stations have not depressed their run buttons in time designated since
the first stations run buttons were depressed. All active stations
must be depressed within a set time after the first station is
depressed in order for the PP150 to see a valid run signal. When this
message shows, release the run buttons and try again making sure all
active run stations are used at the same time. If a run station is not
being used, it must be bypassed correctly using the corresponding
bypass terminal block on the PP150. See the electrical prints for
bypassing the run stations.
Message Code 7 & 107 – WATCHDOG CHK FLT MUST RESTART This
error occurs when the PP150 program has come across an internal
error. If this happens, the PP150 must be restarted. If the fault
persists, contact Toledo Integrated Systems for further
assistance.
Message Code (8&108), (10&110) – WATCHDOG (1&2) MONITOR FAULT
The PP150 has dual processors, each having a force guided watchdog
relay. The watchdog relay is used to remove power to the clutch
valves if a major fault occurs. These relays are checked for proper
operation at startup and are continuously monitored for the correct
state. To reset this fault, Attempt to reset with the PP150 Flt reset
PB. If the PB will not reset the fault, cycle power to the PP150.
If the error persists, contact Toledo Integrated Systems for further
assistance.
Summary of Contents for Press Pilot 150
