manualshive.com logo in svg

TOHATSU MFS 115A, Owner'S Manual

Share
Download
TOHATSU MFS 115A Owner'S Manual Download Page 82

INSPECTION AND MAINTENANCE

82

10

ENOW00969-0

When transporting or storing the outboard
motor, it places only in a vertical position
(normal running position).

ENOM00950-0

Adding a fuel stabilizer

When adding a fuel stabilizer additive
(commercially available), first fill the fuel
tank with fresh fuel. If the fuel tank is only
partially filled, air in the tank can cause
the fuel to deteriorate during storage. 

1. Before adding fuel stabilizer additive,

dr ain   th e   v ap or   s e par a tor   ( S e e
page 83).

2. Follow the instructions on the label

when adding the fuel stabilizer addi-
tive. 

3. After adding the additive, let the out-

board motor run in the water for 10
minutes to make sure any old fuel in
the fuel system has been completely
replaced by the fuel with additive.

4. Turn the engine OFF

ENON00945-0

Note

Over time, oxidation of gasoline can form
buildup of harmful solids called gums.
Water and impurities in the fuel system
can cause corrosion. To stabilize the fuel
and prevent oxidation, gum buildup, and
corrosion throughout the boating season,
recommended to add a good fuel stabilizer
to the fuel tank after each fill up. 

  

CAUTION 

ENOF02421-0

Summary of Contents for MFS 115A

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands