manualshive.com logo in svg

TOHATSU MFS 115A, Owner'S Manual

Share
Download
TOHATSU MFS 115A Owner'S Manual Download Page 45

ENGINE OPERATION

45

7

Buzzer short sounded one time, when set
to 650 min

-1

 (rpm) engine speed, and tells

the lowest engine speed was set.
Buzzer short sounded twice, when set to
850 min

-1

 (rpm) engine speed, and tells

the highest engine speed was set.
Reset the engine speed when af ter
engine restarted and or engine speed is
above 3,000 min

-1

 (rpm), and then trolling

engine speed to be 700 min

-1

 (rpm) as

standard.
In addition, this function does not oper-
ate when battery voltage is lower than
specified, set engine idle and trolling
engine speed to 700 min

-1

 (rpm) auto-

matically.

ENOM00046-A

ENOW00964-0

Before departure, make sure that the boat is
properly moored and no swimmer(s) is near
the  boat  then  che ck  shift  and  ste er ing
mechanism work smoothly.

ENOW00967-0

z

Attach other end of emergency stop
switch lanyard to the operator's PFD (Per-
sonal Flotation device) or arm and keep it
attached during cruising.

z

Do not attach the lanyard to a part of
clothing that can be torn easily when
pulled. 

z

Arrange the lanyard so that will not be
caught by any object when pulled.

z

Be careful not to pull the lanyard acciden-
tally during cruising. Unintentional stop of

engine can cause loss of control of out-
board motor. Rapid loss of engine power
can lead to falling down or causing pas-
senger(s) to be thrown overboard.

ENOW00042-0

z

Do not shift into Reverse during planing,
or control will be lost leading to serious
personal injury, boat may swamp, and/or
hull may be damaged.

z

Do not shift into Reverse during cruising,
or control may be lost, falling down or
causing passenger(s) to be thrown over-
board. Leading to serious personal injury,
and ste er ing system and /or shif ting
mechanism may be damaged.

ENOW00861-0

Do not shift at high boat speed, or control
may be lost, falling down or causing passen-
ger(s) to be thrown overboard. Leading to
serious personal injury.

ENOW00867-0

Sudden acceleration and deceleration may
cause passenger(s) to be thrown overboard
or falling down.

ENOW00862-0

Gear and clutch damage may occur if shifting
at high engine speed.
Engine must be in the slow idle position
before shifting is attempted.

ENOW00863-0

Idle speed may be higher during warming up
of engine. If shifted to Forward or Reverse

4. Forward, reverse, and 

acceleration

  

WARNING

  

WARNING

  

WARNING

  

WARNING

  

WARNING

  

CAUTION

  

CAUTION

Summary of Contents for MFS 115A

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands