TOHATSU MD 30B2 Owner'S Manual Download Page 61

Page: 61 / 92

ENGINE OPERATION

②

Operate the Power Trim & Tilt

switch and tilt and engine up.

The engine can also be tilted up using
the switch provided under the Lower
Engine Cover.

③

Lock the tilt with the Tilt stopper

after the engine has been tilted up.

④

To tilt the engine down, Turn the

Reverse  Lock  Lever  upward
(toward  "LOCK").  Tilt  the  engine
up slightly and then let it go down.
(The  Reverse  Lock  will  be  set
automatically.)

EFTO, EPTO type

①

Disconnect the fuel connector from

the engine.

30 · 40 · 50

・

115

It is possible to tilt up or down in

spite of main switch "ON" or "OFF".

Reverse

lock lever

Tilt stopper

Trim rod

・

115

Tilt Stopper

30 · 40 · 50

OM_E_MD30B2-115A2_body_111213.indd 61

11/12/13 13:07

Summary of Contents for MD 30B2





























































































Search results

Summary of Contents for MD 30B2

Reviews:

Related manuals for MD 30B2

Brands by name

Popular brands

TOHATSU MD 30B2, Owner'S Manual

Search results

Summary of Contents for MD 30B2

Reviews:

Related manuals for MD 30B2

Brands by name

Popular brands