TOHATSU BFT 2000A Owner'S Manual Download Page 98 | Manualshive

Page: 98 / 126

background image

95

MAINTENANCE

13. Align the aligning mark as shown

in the figure, when installing the
suspension strap on the water
separator.

14. The drain joint should be

positioned within the protruded
portion of the suspension strap as
shown in the figure.

15. Prime the engine using the

priming bulb (see page 48). Check
for fuel leaks. Repair any fuel
leaks if necessary.

If the buzzer sounds, water or
sediment accumulation is found to be
caused by excessive water or
sediment accumulated in the fuel
filter, inspect the fuel tank. Clean the
fuel tank if necessary.

EMISSION CONTROL SYSTEM

The combustion process produces
carbon monoxide and hydrocarbons.
Control of hydrocarbons is very
important because under certain
conditions, they react to form
photochemical smog when subjected
to sunlight. Carbon monoxide dose
not react in the same way, but it is
toxic.

Problems that May Affect Outboard
Motor Emissions

If you are aware of any of the
following symptoms, have the
outboard motor inspected and
repaired by your dealer:
1. Hard starting or stalling after

starting

2. Rough idle
3. Misfiring or backfiring during

acceleration

4. Poor performance (driveability)

and poor fuel economy

WATER SEPARATOR

ALIGNING MARK

SUSPENSION
STRAP

PROTRUDED PORTION

SUSPENSION STRAP

DRAIN JOINT

«
...
96
97
98
99
100
...
»

Summary of Contents for BFT 2000A































































































































Reviews:

No comments

Related manuals for BFT 2000A

Brand: Yamaha Pages: 497

Brand: Atmel Pages: 22

Brand: Texas Instruments Pages: 16

Brand: Maxus Pages: 59

Brand: JETWAY Pages: 46

Brand: Zeal-All Pages: 9

Brand: AOpen Pages: 125

Brand: AOpen Pages: 8

Brand: Biostar Pages: 33

Brand: Fujitsu Pages: 72

Brand: ASROCK Pages: 67

Brand: Abit Pages: 88

Brand: JETWAY Pages: 48

Brand: JETWAY Pages: 54

NLBT-I1800 Series

Brand: JETWAY Pages: 51

Brand: JETWAY Pages: 51

Brand: DTK Pages: 38

Brand: ADLINK Technology Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands