TOHATSU BFT 2000A Owner'S Manual Download Page 81 | Manualshive

Page: 81 / 126

background image

78

TRANSPORTING

3. Secure the outboard motor on an

outboard motor stand with the
mounting bolts and nuts.

4. Remove the hoist hook and

reinstall the engine cover (see page
39).

Trailering

When trailering or transporting the
boat with the outboard motor
attached, it is recommended that the
outboard motor remain in normal
running position.

Do not trailer or transport the boat
with the outboard motor in the
tilted position. The boat or
outboard motor could be severely
damaged if the outboard motor
drops.

The outboard motor should be
trailered in the normal running
position. If there is insufficient road
clearance in this position, then trailer
the outboard motor in the tilted
position using an outboard motor
support device such as a transom
saver bar, or remove the outboard
motor from the boat.

OUTBOARD MOTOR STAND

«
...
79
80
81
82
83
...
»

Summary of Contents for BFT 2000A































































































































Reviews:

No comments

Related manuals for BFT 2000A

Brand: MSI Pages: 35

Brand: Abit Pages: 104

Brand: AOpen Pages: 156

Brand: Elitegroup Computer Systems Pages: 82

Brand: ablelogic Pages: 47

Brand: VIA Technologies Pages: 76

Brand: Xilinx Pages: 55

Brand: Gigabyte Pages: 136

Brand: Xilinx Pages: 56

Brand: IBASE Technology Pages: 72

MPG Z390 GAMING EDGE AC

Brand: MSI Pages: 87

Brand: Mercury Pages: 102

Brand: MSI Pages: 73

Super 7 SY-5SSM

Brand: SOYO Pages: 86

Brand: Gigabyte Pages: 88

Brand: Picor Pages: 11

Brand: Global Pages: 33

Brand: DFI Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands