TOHATSU BFT 2000A Owner'S Manual Download Page 101

Page: 101 / 126

MAINTENANCE

Fuse

Before replacing the fuse, check the
current ratings of the electrical
accessories and ensure that there are
no abnormalities.

• Never use a fuse with a different

rating from that specified.
Serious damage to the electrical
system or a fire may result.

• Disconnect the battery cable at

the battery negative (–) terminal
before replacing the fuse.
Failure to do so may cause a
short circuit.

If the fuse is blown, check the
cause, then replace the fuse with a
spare fuse of the same rated
capacity. Unless the cause is found,
the fuse may blow again.

<Replacement>

1. Stop the engine.
2. Disconnect the battery (see page

97).

3. Remove the engine cover (see page

39).

4. Open the junction box cover.

5. Pull the old fuse out of the clip with

the fuse puller supplied in the fuse
box.

6. Push a new fuse into the clips.

SPARE FUSES
(10 A, 15 A, 30 A)

FUSES
(10 A, 15 A, 30 A)

FUSE PULLER

JUNCTION
BOX COVER

FUSE PULLER

BLOWN FUSE

Summary of Contents for BFT 2000A































































































































Search results

Summary of Contents for BFT 2000A

Reviews:

Related manuals for BFT 2000A

Brands by name

Popular brands

TOHATSU BFT 2000A, Owner'S Manual

Search results

Summary of Contents for BFT 2000A

Reviews:

Related manuals for BFT 2000A

Brands by name

Popular brands