TOHATSU BFT 2000A Owner'S Manual Download Page 75

Page: 75 / 126

OPERATION

3. If the overheat warning system

stays activated, stop the engine.
Tilt up the outboard motor and
check the water intakes for
obstructions. If there are no
obstructions at the water intakes,
return to the closest boat landing
and contact your outboard motor
dealer.

When the PGM-FI activated:

1. Consult with your outboard motor

dealer.

When the ACG warning system is
activated.

1. Check the battery (see page 96). If

the battery is OK, consult with your
outboard motor dealer.

When the water separator buzzer
sounds:

1. Check the water separator for water

contamination. If water is
accumulated, drain them (see page
91).

COOLING WATER INTAKE PORT
(each side)

WATER SEPARATOR

Summary of Contents for BFT 2000A































































































































Search results

Summary of Contents for BFT 2000A

Reviews:

Related manuals for BFT 2000A

Brands by name

Popular brands

TOHATSU BFT 2000A, Owner'S Manual

Search results

Summary of Contents for BFT 2000A

Reviews:

Related manuals for BFT 2000A

Brands by name

Popular brands