TOHATSU BFT 2000A Owner'S Manual Download Page 19 | Manualshive

Page: 19 / 126

background image

16

CONTROLS AND FEATURES

Shifting gear into forward, reverse, or
neutral and the engine speed
adjustment can be performed with the
remote control lever.
It is necessary to pull up the neutral
release lever to operate the remote
control lever.

FORWARD:
Moving the lever to the FORWARD
position (i.e. approximately 35° from
the NEUTRAL position) engages the
gear into forward. Moving the lever
further from the FORWARD position
will increase the throttle opening and
the boat forward speed.

NEUTRAL:
Engine power is cut off from the
propeller.

REVERSE:
Moving the lever to the REVERSE
position (i.e. approximately 35° from
the NEUTRAL position) engages the
gear into reverse. Moving the lever
further from the REVERSE position
will increase the throttle opening and
the boat reverse speed.

Remote Control Lever (R2 type)

REMOTE CONTROL LEVER

NEUTRAL
RELEASE
LEVER

FORWARD

NEUTRAL

REVERSE

MAXIMUM

FORWARD

NEUTRAL

REVERSE

MAXIMUM

REMOTE
CONTROL LEVER

SHIFT

SHIFT

35°

35°

THROTTLE OPENING

THROTTLE
OPENING

MINIMUM

MINIMUM

«
...
17
18
19
20
21
...
»

Summary of Contents for BFT 2000A































































































































Reviews:

No comments

Related manuals for BFT 2000A

Brand: Aaeon Pages: 122

Brand: Aaeon Pages: 52

Brand: Aaeon Pages: 99

Brand: ECS Pages: 52

Brand: Texas Instruments Pages: 8

Brand: Intel Pages: 89

Brand: Mercury Pages: 41

Brand: TYAN Pages: 117

Brand: BIGTREETECH Pages: 39

Brand: Quick Pages: 32

Brand: JETWAY Pages: 38

Brand: NXP Semiconductors Pages: 35

Brand: Supermicro Pages: 124

Brand: Gigabyte Pages: 20

Brand: Exar Pages: 9

Brand: ON Semiconductor Pages: 20

Brand: AOpen Pages: 8

Brand: Advantech Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands