TOELLNER TOE 9261 Instruction Manual Download Page 20

 

Section 4 

– Technical Data 

 

 

TOELLNER Electronic Instrumente GmbH 

20 

(Technical data, cont.) 

General

 

 

Mains voltage 

Wide-range input 

90…264 V AC, 47-63 Hz, I

max

 = 0.4 A,  

rear appliance plug with fuse T1AL according to IEC 127-2/III, 
DIN 41662 

Power consumption, mains side 

Max. 35 VA 

Protection 

Protection Class I according to DIN EN 61140 

 

Degree of protection IP20 according to IEC 60529 

 

Overvoltage category II according to IEC 60664-1 

 

Pollution degree 2 according to IEC 60664-1 

Operating temperature 

0 - 40°C 

Storage temperature 

−20 - 70°C 

Reference temperature 

23°C ±1°C 

Cooling 

2-stage thermostatically controlled fan 

Overall dimensions (W x H x D) 

224 mm x 103 mm x 348 mm 

Rack mount dimensions (W x H x D) 

224 mm x 88 mm x 325 mm 

19" system 

Compatible with ½ 19", 2 HU 

Weight 

Approx. 4 kg 

Housing 

Aluminum/steel 

 
 
 

4.2 

General data 

 

 

Ordering 
options

 

  0-50 A, 0-60 V ..... TOE 9261-50 
0-100 A, 0-60 V ..... TOE 9261-100 

 

 

Included 
accessories

 

1 mains cable 
2 terminal blocks for signal line switches 
1 Instruction Manual 
 

Optional 
accessories

 

0.50 m connection cable with 1 safety socket, red ........................................... TOE 9260/22 
0.50 m connection cable with 1 safety socket, blue .......................................... TOE 9260/23 
1.20 m connection cable with 1 safety socket, red ........................................... TOE 9260/24 
1.20 m connection cable with 1 safety socket, blue .......................................... TOE 9260/25 
19" adapter set 2 HU (asymmetrical) for 1x TOE 9261 .................................... TOE 9521 
19" adapter set 2 HU (parallel connector) for 2 Toellner Instruments ½ 19" .... TOE 9522 
 
 
 

4.3 

Specification of the high-current connectors 

 
The 

built-in high-current connectors of the TOE 9261 are the following components

TOE 9261-50......... Safety flush-mounting plug, type ID/S6AR-N-B4S, manufacturer Multi-

Contact 

TOE 9261-100 ...... Safety flush-mounting plug, type ID/S6AR-N-S, manufacturer Multi-

Contact 

 
Suitable counter piece for crimping assembly on cables is the following: 
TOE 9261-50 and TOE 9261-100 ....... Safety socket, type KBT6AR-N/16-S, manufacturer 

Multi-Contact. 
This counter piece can only be attached to a cable by 
crimping assembly using special tooling, soldering is 
impossible. 

 

Summary of Contents for TOE 9261






















Reviews: