TM 2008 4 Stroke, User Manual

Page: 11 / 80

ENGLISH
ENGLISH ENGLISH
11
ELECTR ELECTR ELECTR ELECTR ELECTRONIC ONIC ONIC ONIC ONIC T T T T TA A A A ACHOMETER (END/SMR/SMM) CHOMETER (END/SMR/SMM) CHOMETER (END/SMR/SMM) CHOMETER (END/SMR/SMM) CHOMETER (END/SMR/SMM)
The electronic tachometer display is always activated.
The electronic tachometer is powered by an SR44 1.5 Volt battery,
(D357) 11.6x5.4mm.
Replace the battery every 2 years or in case of blurring of the display.
To replace the battery, open the cover positioned on the rear using a
screwdriver, and extract the battery.
Insert the new battery in a way that the positive pole is visible from the
outside and close the cover.
Before extracting the battery, make note of the WS (wheel circumference)
and DST (total mileage) values.
These values will be re-programmed into the instrument after battery
replacement.
MODE SELECTION AND RESET MODE SELECTION AND RESET
MODE SELECTION AND RESET MODE SELECTION AND RESET MODE SELECTION AND RESET
(END/SMR/SMM) (END/SMR/SMM)
(END/SMR/SMM) (END/SMR/SMM) (END/SMR/SMM)
While the electronic tachometer always displays the speed of the vehicle
expressed in Kmh (or Mph on the basis of the selection made) it also
allows to visualise the following functions on selection:
TRP
Daily mileage
AVS Average speed (after 10 hours or 1000Km press RESET)
STP Chronometer (start and stop autom. max. time 10 hours)
MAX Max. speed reached (from the last RESET)
DST Total mileage (up to 99999Km)
CLK
Clock
To reset theTRP, AVS, STP and MAX functions, press the right button (blue).
Select the function and press the left button for 5 sec. (yellow).
The values displayed are zeroed.
P P
P P
PR R
R R
ROGRAMMING OGRAMMING
OGRAMMING OGRAMMING
OGRAMMING THE ELECTR THE ELECTR
THE ELECTR THE ELECTR
THE ELECTRONIC ONIC
ONIC ONIC
ONIC T T
T T
TA A
A A
ACHOMETER CHOMETER
CHOMETER CHOMETER
CHOMETER
(END/SMR/SMM) (END/SMR/SMM)
(END/SMR/SMM) (END/SMR/SMM)
(END/SMR/SMM) (only after battery replacement)
Remove the connector positioned on the back of the instrument.
Press the grey button on the rear of the instrument for 5 seconds. Four
numbers appear on the display, of which the first is flashing. “WS”
(Wheel Size) also flashing, appears in the top right of the display.
Now press in sequence, the left hand button (yellow) to change the
value of the first flashing number.
Press the right hand button (blue) to make the second number flash
and press the left hand (yellow) button in sequence to visualise the
desired value.
Repeat the operation to change the value of the following number and
so on until the exact development of the wheel expressed in mm. (=tyre
diam. in mm.x3.14) is visualised.
Finally, with the 4th number still flashing, to change the unit of
measurement from Kmh to Mph, press the right hand button (blue)
and “Kmh” will start to flash,now press the left hand button (yellow) to
pass to “Mph”.
End programming by pressing the grey button on the rear of the
instrument for 1 sec.
OPERA OPERA
OPERA OPERA OPERATING CONTR
TING CONTR
TING CONTR TING CONTR TING CONTROLS
OLS
OLS OLS OLS
OPERA OPERA
OPERA OPERA
OPERATING CONTR TING CONTR
TING CONTR TING CONTR
TING CONTROLS OLS
OLS OLS
OLS