background image

POLE PRUNER 750W  TTB426GDO

8. SHARPENING SAW CHAIN

It is highly recommended that, once the saw chain loses its 

ability to cut cleanly and safely, it is replaced. It is possible, 

however, to sharpen the existing chain if done carefully. (See 

Fig.17a, 17b & 17c)

1). Ensure the chain is correctly tensioned.

2). Use a round file with a diameter of 1.1 times the cutting 

tooth depth. Make sure 20% of the file diameter is above the 

cutter’s top plate.

3). File at an angle perpendicular to the bar, and at an angle 

of 25° to the direction of travel.

4). File each tooth from the inside towards outside only. File 

one side of the chain first, then turn the pruner around and 

repeat the process.

5). Sharpen each tooth equally by using the same number 

of strokes.

6). Keep all cutter lengths equal.

7). Check the safety depth gauge height every 5 

sharpenings.

8). If the depth gauges are also trimmed it is essential that 

the original profile be restored.

9). Use a depth gauge measuring instrument to check the 

height of the depth gauge.

9. ORDERING REPLACEMENT PARTS

Please quote the following data when ordering replacement 

parts:

- Type of machine

- Article number of the machine

- Identification number of the machine

- Replacement part number of the part required

Fig. 17a

Fig. 17b

Fig. 17c

Summary of Contents for TTB426GDO

































Reviews: