manualshive.com logo in svg

Titan Logix CTX-TDS-100, Configuration Utility Manual

Share
Download
Titan Logix CTX-TDS-100 Configuration Utility Manual Download Page 35

 

TPM 054 

Version 1.0, May 30, 2016 

Page | 33  

SOFTWARE 

Configuration Utility Manual

 

GATEWAY HEALTH CHECK 

 

The Gateway Health Check is a quick test to confirm that the Gateway is operating normally or to verify 
a failure. It uses visual observation of the status light and the Configuration Utility to determine the 
health of the system. Failure of any checklist step below indicates a problem to be resolved. 

This check is easily performed remotely through a Wi-Fi connection. Note that the vehicle must provide 
adequate power for a successful health check. Error free steps 2 through 6 imply that the Status light is 
indicating normally. 

 

Step 

Detail 

 

1.

 

Observe the Gateway Status 
light 

Confirm: Blinking ½ second ON, ½ second OFF 

 

2.

 

Launch the Gateway 
Configuration Utility 

Establish a Wi-Fi connection with the Gateway 

Click the “Gateway Status” selection

 

 

3.

 

Finch II communication 

Confirm: Communication Established, checked 

 

4.

 

Cellular connection 

Confirm the following: 

•

 

PPP Link Status, checked 

•

 

Signal Strength, good 

 

5.

 

Remote server connection 

Confirm: Communication Established, checked 

 

6.

 

GPS data 

Confirm the following: 

•

 

Communication Status, checked 

•

 

GPS Fix Status, checked 

 

 

 

 

Summary of Contents for CTX-TDS-100








































Reviews:

No comments

Brands by name

Popular brands

Load more brands