manualshive.com logo in svg

tiki 1005-51, English Manual

Share
Download
tiki 1005-51 English Manual Download Page 29

ENGLISH – Tiki start

 29

4.2  Use with the external battery

1.  Before use, charge both the internal and the external battery.
2.  If the indicator light on the battery charger is red, the battery is charging.
3.  If the indicator light on the battery charger is green, the battery is fully charged, 

refer to figure 2.

4.  At the moment that both the internal and the external battery are fully charged, 

perform the following:
a.  Pull the charging cable through the tri-glide on the harness to make sure the 

cable has a strain relief and that it proceeds backwards behind the user.

b.  Remove the screw seal or red tape on the top left of the mask.
c.  Insert and screw the cable of the external battery to the internal battery, 

making sure to observe that the pin configuration’s meet, refer to figures  
3 and 8.

d.  Connect the cable to the external battery.

5.  Use the Tiki start as to the below procedures.
6.  After use, unscrew the cable from the internal battery, refer to figure 3. Do not 

leave the external battery connected to the internal battery when the mask is not 
in use. If not disconnected, the batteries discharge rapidly.

7.  Note that the red tape or srew seal in step 4a is to be applied again if the  

Tiki start is to be used with the internal battery only again, refer to paragraph:  
1.4 Prepare the Tiki start on page 7.

30°

Summary of Contents for 1005-51

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands