background image

Please retain instructions for future reference

CAUTION:

All buildings should be erected
by two competent adults.

CAUTION:

It is advisable to wear safety
gloves during building installation.

Whilst all products manufactured are made to the highest standards of safety and in the case of children’s products independently tested to 
EN71 level, we cannot accept responsibility for your safety whilst erecting or using this product.

GO WITH THE PRO!:

We understand how busy life can be: our Pro-Installation service can take the stress and strain out of assembling your 
quality Tiger building for you. We recommend using professional and dedicated installers to erect your building. With their 
knowledge and experience, they will ensure that your cabin is put properly in place ready for you to enjoy your space for 
years to come.

If you have not booked our Pro-Installation service and would like to arrange an installation, please contact our friendly 
customer team on 0113 205 4189 (Mon – Fri 9am-5pm) or email [email protected].

• The pro-install team will contact you to arrange a suitable time and date for the fitting. 
• Sit back, relax and let our professional home installation service do all the hard work for you!
• Please view our Pro Installation page for full terms and conditions.

MADE IN THE UK SINCE 1913.

We have been making our high quality, great 
value sheds here in Britain for decades.

03

Summary of Contents for TIGERFLEX ZORA

























Reviews: