background image

BEFORE YOU GET STARTED

04

tigersheds.com

0113 205 4189

[email protected]

TOOLS REQUIRED

We recommend using the following tools (not supplied):

SCREW

FIXING PACK CONTENTS:

RUBBER MALLET

DRILL

LADDER

TAPE MEASURE

SHARP KNIFE

SPIRIT LEVEL

13mm Galvanised Clout Nails

(C13) x80

25mm Black Screws

(S25) x16

35mm Screws

(S35) x200

30mm Galvanised Nails

(N30) x140

30mm Galvanised Nails

(N40) x20

40mm Screws

(S40) x24

50mm Screws

(S50) x18

IMPORTANT

•  Before assembly please make sure you have a suitable base ready to erect your building on.
•  This base MUST be level and flat to ensure that the building is assembled properly and lines up.
•  Please carefully unpack the components in your delivery, and remove the untreated timber supports that make up the
 

boxed pallet.

• 

DO NOT

 start your build until you have checked that all the parts of your building are present and in a suitable condition.

•  If you are organising a third party to install your building, it is best practice not to schedule this immediately on receipt of your 
 

order, to give you time to check your delivery.

HAMMER

WOOD SAW

Summary of Contents for TIGERFLEX ZORA

























Reviews: