Tiger TIGERFLEX ZORA Page 22 Assembly Instructions Manual Download

Page: 22 / 24

tigersheds.com

0113 205 4189

[email protected]

14’x6’ TIGERFLEX

ZORA LOG CABIN INSTRUCTIONS

Step 16:

FELTING THE ROOF

• Roll out felt along lower part of roof, leaving sufficient overhang to fold down onto roof edge.

Note: Do not fold underneath roof.

• Use clout nails

(C13)

to tack top of felt section 1 to the roof panels. Repeat for felt section 2.

• Fold the overhanging felt at ends under roof panel and tack in place.

• Felt section 3 should overlap the lower strips and tack into place.

Ridge piece should

overlap the lower strips

and tack into place.

C13

Step 17:

BARGE BOARDS & FINIAL

(MODULE PACKS: R)

•  Fit barge boards to the roof panels,
  trapping overhanging end of the felt
  in between to provide a weather
  proof seal. Secure using 2x 40mm

(N40)

nails per barge board

• Secure finial over the top of the
barge boards using 2x 40mm

(N40)

nails

per barge board

N40

Summary of Contents for TIGERFLEX ZORA

























Search results

Summary of Contents for TIGERFLEX ZORA

Reviews:

Related manuals for TIGERFLEX ZORA

Brands by name

Popular brands

Tiger TIGERFLEX ZORA, Assembly Instructions Manual

Search results

Summary of Contents for TIGERFLEX ZORA

Reviews:

Related manuals for TIGERFLEX ZORA

Brands by name

Popular brands