Tiger JPD-A Series, Operating Instructions Manual

Page: 12 / 74

23
22
English
7
4·7
6
5
8
2
3
Timer function (Timer 1/Timer 2)
You can preset the time that you want cooking
to be actually completed.
• Select either “Timer 1” or “Timer 2” and set the
desired completion time. The cooking is completed
at the preset time.
• The preset timer settings are stored in the memory
and “Timer 1” and “Timer 2” can be both set.
• It is useful to set the times that you use often.
Note
● Example: If “Timer 1” is set to 13:30, cooking is
completed at 13:30.
1
Connect the power cord.
Appliance plug
(1) Insert the
plug.
Power plug
(2) Insert the
plug.
2
Check the current time.
• See P.52 for the procedure to set the
current time.
Blinks
Check the
current time.
3
Press the [Menu/ ◀▶ ] key
to select the desired menu

P.18 .
• It is not necessary to press the [Menu/
◀▶
]
key if the desired menu is already selected.
Blinks
Short
beep
Check
that the
Keep Warm lamp is off.
4
If you select the “Porridge”
menu, use the [Hr] and [M] keys
to set the desired cooking time.
• Pressing the [Hr] key increases the time by 5
minutes while the [M] key decreases it by 5
minutes.
• The cooking time can be set between 40 and
90 minutes in increments of 5 minutes.
Increases by 5 min.
Decreases by 5 min.
• The default setting is 60 minutes. Adjust the
time as desired.
5
Select the Keep Warm setting
for after cooking

P.18 .
• You do not need to select the Keep Warm
setting if the desired setting has been
selected.
Using the Timer Function
6
Press the [Timer] key to select
either “Timer 1” or “Timer 2”.
The selected setting switches between “Timer
1”, “Timer 2”, and “Soak Timer” each time the
[Timer] key is pressed.
• For the Soak Timer function, see P.24.
Blinks
Blinks
Blinks
Short
beep
The previous preset
time is displayed.
• The previously preset time is displayed. It
is not necessary to set the timer again if the
desired completion time is already displayed.
Note
● The Timer function is not available in the following
cases.
• When the “Quick”, “Rapid
<=
1 Cup”, “Sweet”,
“Mixed”, “Slow Cook”, “Soup”, or “Clean care”
menu is selected
• When “0:00” is blinking on the display
• When the inner pot is not set
● If the Keep Warm lamp is on, press the [Cancel]
key to turn off the lamp. (The Timer function is not
available while the Keep Warm lamp is lit.)
● Dark brown crisp rice may be formed when the
timer setting is extended. If this is an issue, rinse
the rice or barley well.
Timer setting guidelines for each menu
Menu Timer setting guideline
Eco 50 min. or more
Plain 55 min. or more
Ultra 1 hr. 15 min. or more
Long-grain 45 min. or more
Porridge Cooking time + 1 min. or more
Multigrain 55 min. or more
Brown 1 hr. 15 min. or more
Brown GABA 4 hr. 30 min. or more
Sushi 55 min. or more
• When the preset time is less than the timer
setting guideline, cooking may not be completed
at the preset time.
„
Sounds emitted by the rice cooker
● If you do not operate the rice cooker within
approximately 30 seconds after pressing the [Timer]
key, the rice cooker beeps 2 times (short beeps).
● If the [Timer] key is pressed while the rice cooker is in
a state where the Timer function is not available, the
rice cooker beeps 2 times (short beeps).
● If the sound becomes bothersome, the volume
can be adjusted. (See P.47.)
7
Use the [Hr] and [M] keys to set
the desired completion time.
• The current time is displayed in a 24-hour
format.
Blinks
Blinks
Blinks
Short
beep
• Press the [Hr] key to change the set time
in increments of 1 hour. Press the [M] key
to change that time in increments of
10 minutes.
• Hold down the corresponding key to change
the time more rapidly.
Note
● Do not set the timer to more than 12 hours, as it
may result in spoiled rice.
8
Press the [Start] key once.
The Timer function is set.
For “Plain” menu
For other menus
On
On
On
Long
beep
Short and
long beep
• If you make a mistake or otherwise want to
reset the timer, press the [Cancel] key and
repeat the procedure from step
3
on P.22.