SAFETY
BOOM
Safety Section 1-14
© 2015 Alamo Group Inc.
SAFETY
HAZARDS WITH MAINTENANCE OF IMPLEMENT
AVOID SERIOUS INJURY OR DEATH FROM COMPONENT FAILURE BY KEEPING IMPLEMENT IN
GOOD OPERATING CONDITION IN PERFORMING PROPER SERVICE, REPAIRS AND
MAINTENANCE.
BEFORE PERFORMING SERVICE, REPAIRS AND MAINTENANCE ON THE IMPLEMENT:
•
STOP ENGINE AND PTO
, engage parking brake, lower implement, allow all moving parts to stop and remove key before
dismounting from tractor.
•
PLACE
implement on ground or securely block up raised equipment. Use large blocks on soft or wet soil.
•
PUSH
and
PULL
Remote Hydraulic Cylinder lever to relieve hydraulic pressure.
•
DISCONNECT Pump solenoid valve or PTO driveline connection before servicing mower head
.
•
WEAR SAFETY GLASSES, PROTECTIVE GLOVES
and follow
SAFETY PROCEDURES
when performing service, repairs
and maintenance on the implement:
•
Always
WEAR
protective
GLOVES
when handling blades, knives, cutting edges or worn component with sharp edges.
•
Always
WEAR GLOVES
and
SAFETY GLASSES
when servicing hot components
•
AVOID CONTACT
with hot hydraulic oil tanks, pumps, motors, valves and hose connection surfaces.
•
SECURELY
support or
BLOCK UP
raised implement, framework and lifted components before working underneath equipment.
•
FOLLOW INSTRUCTIONS
in maintenance section when replacing hydraulic cylinders to prevent component falling.
•
STOP
any implement movements and
SHUT-OFF TRACTOR
engine before doing any work procedures.
•
USE
ladder or raised stands to reach high equipment areas inaccessible from ground.
•
ENSURE
good footing by standing on solid flat surfaces when getting on implement to perform work.
•
FOLLOW
manufacturer's instructions in handling oils, solvents, cleansers, and other chemical agents.
•
DO NOT
change any factory-set hydraulic calibrations to avoid component or equipment failures.
•
DO NOT
modify or alter implement, functions or components.
•
DO NOT WELD
or repair rotating mower components. These may cause vibrations and component failures being thrown from
mower.
PERFORM SERVICE, REPAIRS, LUBRICATION AND MAINTENANCE OUTLINED IN IMPLEMENT MAINTENANCE
SECTION:
•
INSPECT
for loose fasteners, worn or broken parts, leaky or loose fittings, missing or broken cotter keys and washers on pins, and
all moving parts for wear.
•
REPLACE
any worn or broken parts with authorized service parts.
•
Inspect mower blade spindle to ensure bearing preload. If loose repair before operating.
•
LUBRICATE
unit as specified by lubrication schedule
•
NEVER
lubricate, adjust or remove material while it is running or in motion.
•
TORQUE
all bolts and nuts as specified.
BLADE INSPECTION:
•
Inspect blade carrier and blades daily.
•
Check blade and blade carrier BOLT TORQUE daily. Loose bolts can cause blade or blade bolt failures.
•
REPLACE, bent, damage, cracked and broken blades immediately with new blades.
•
AVOID
blade failures and thrown broken blades.
DO NOT
straighten, weld, or weld hard-facing blades.
SAFETY SHIELDS, GUARDS AND SAFETY DEVICES INSPECTION:
•
KEEP
all Deflectors, Chain Guards, Steel Guards, Gearbox Shields, and PTO integral shields, Bands, Side Skirts and Skid Shoes
in place and in good condition.
•
REPLACE
any missing, broken or worn safety shields, guards and safety devices.
•
Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California
to cause cancer, birth defects or other reproductive harm.
•
Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the state of California to
cause cancer, birth defects or other reproductive harm.
PN HMBM-01
Summary of Contents for BENGAL JD6110-20M/R MY20
