manualshive.com logo in svg

TIA WAVEJET 400-1338-02, Component Maintenance Manual With Illustrated Parts List

Share
Download
TIA WAVEJET 400-1338-02 Component Maintenance Manual With Illustrated Parts List Download Page 21

 

WAVEJET MICROWAVE OVEN 

COMPONENT MAINTENANCE MANUAL 

WITH ILLUSTRATED PARTS LIST 

 

 

25-30-43

 

Page

 

101 

March 15, 2003 

 

TESTING AND TROUBLESHOOTING

 

 

WARNING 

 

FOR SAFETY REASONS, TWO PEOPLE SHOULD ALWAYS BE PRESENT DURING 

ALL TESTING AND TROUBLESHOOTING.  WHEN POWER IS APPLIED TO THE UNIT, 

LETHAL VOLTAGES IN EXCESS OF 5000 VOLTS ARE PRESENT WITHIN THE 

MICROWAVE OVEN.  DO NOT ASSUME THAT ANY ELECTRICAL CONNECTION IS 

SAFE TO TOUCH SINCE MALFUNCTIONING COMPONENTS COULD CAUSE 

DANGER.  A SAFE CONNECTION COULD BECOME HOT AND DANGEROUS. 

 

MAKE CERTAIN THAT A GOOD ELECTRICAL GROUND BETWEEN  

CHASSIS AND EARTH IS MAINTAINED AT ALL TIMES.

 

 

NOTE: 

Extreme care must be taken to avoid measuring probe slippage or accidental 
shorting of terminals while power is applied to units. 

 

1. 

General 

 

A. 

This section consists of the following two subsections:  Testing and 
Troubleshooting. 

 

(1)  The Test subsection is a general functional test of the microwave oven to 

determine in which area a fault may have occurred. 

 

(2)  The Troubleshooting guide describes the most common possible faults and 

their remedies.  It is meant to serve as a general guide and assumes that 
all internal wiring and power connections are correct. 

 

2. 

Testing 

 
 

A. 

Equipment Needed: 

 

 

 

Microwave Survey Meter 

 

Thermometer ± 1º F 

 

Volt/Ohm meter 

 

 

B. 

Functional Test: 

 

1.  Power Output Test:  Performed to determine if the microwave oven is 

heating to specification. 

Summary of Contents for WAVEJET 400-1338-02






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands