background image

23

EN

H - TECHNiCAL ANd LEGAL iNFOrMATiON

30Nm drive kit 

for rolliNg shutters aNd bliNds

1 - TECHNICAL CHARACTERISTICS

Remote control

Management module

Tubular motor

Radio frequency

Radio frequency

Type

Radio range 

Radio range 

Power supply 

Operating temperature 

Power supply 

Power supply 

Rated torque 

Maximum number of turns 

Number of channels 

Operating temperature 

Speed at rated torque 

Maximum shutter weight 

Number of devices per channel 

Minimum power 

Consumption at rated strength 

Maximum shutter surface 

Operating temperature 

Maximum power 

Assigned operating duration 

ARW 868.3MHz protocol

ARW 868.3MHz protocol

Tubular 230V AC motor, epicyclic reduction gear assembly

Up to 150m in open air*

Up to 150m in open air*

230V AC 50Hz

0°C to 40°C

3V DC via a CR2032 battery

230V AC 50Hz

30Nm

22

4 groups of 3 channels

0°C to 40°C, indoor use only

15 rpm

70 kg

5

5W

0.87a

5.6m² (PVC); 9m² (aluminium); 9m² (wood)

0°C to 40°C, indoor use only

500W

4 min

*The indicated radio range refers to the open air range, i.e. no obstacles between the receiver and the 
transmitter. Any obstacle or disturbance will reduce this range.

Summary of Contents for 500014





























Reviews: