21
SALICRU
4.3.6.3. AS400 Interface with DB9 output
(option).
Ŗ
Communication line (COM) is a very low voltage circuit
of safety. To preserve the quality, it has to be installed
separate from other lines that have dangerous voltages (energy
distribution line).
Ŗ
UPS has a dry contact card for the AS400 communication
protocol, it provides digital signals in a free potential way, with
a maximum applicable voltage and current of 240 V ac or
30 V dc and 1A. Pin-out of the DB9 connector are stated in
figure 10 and detailed in table 5.
Ŗ
The most common use of this type of ports is to provide the
needed information for the closing file software.
Ŗ
For more information, contact with our S.T.S or our nearest
distributor.
UPS fault
General alarm
Ground (GND)
Common
Bypass
Low battery
UPS on
AC mains fault
Fig. 10.
AS400 dry contact pin-out.
Description
Pin-out
Input/output
UPS fault
1
Output
General alarm
2
Output
Ground (GND)
3
Input
Common
5
Input
Bypass
6
Output
Low battery
7
Output
UPS "On"
8
Output
AC mains fault
9
Output
Tabla 5.
AS400 dry contacts alarms.
Installation.
Ŗ
Remove the screws that fix the protection cover of the slot of
the equipment and the own cover.
Ŗ
Take the AS400 card and insert it into the smart slot. Make
sure that it is well connected, so the resistance that the own
connector inside the slot makes has to be overcome.
Ŗ
Fix the card with the previous removed screws.
Ŗ
Connect the DB9 connector from AS400 with the peripheral
to be communicated.
4.3.6.4. Protection against transient voltages for
modem / ADSL / Fax / ... lines.
Ŗ
Communication line (COM) is a very low voltage circuit
of safety. To preserve the quality, it has to be installed
separate from other lines that have dangerous voltages (energy
distribution line).
Ŗ
Connect the main line for the modem / ADSL / Fax /... to the
RJ45 connector of the equipment, labelled as "Input".
Ŗ
Connect the own modem / ADSL / Fax /... to RJ45 connector
of the equipment, labelled as "Output".
4.3.7. Software.
Ŗ
Free software download - WinPower.
WinPower is a UPS monitoring software, which makes a
user-friendly interface of monitoring and management. This
software supplies an auto Shutdown for a system based on
several PCs in case of an electrical blackout. With this soft-
ware, the end-users can monitor and manage any UPS in the
same IT network, through the RS232 or USB communication
port, never mind the distance between them.
Fig. 11.
Main screen of the monitoring software.
Ŗ
Installation procedure:
Go to website:
http://support.salicru.com
Choose the operating platform that you need and follow
the instructions described in the web site to download the
software.
When downloading the needed files from Internet, enter
the following licence to install the software:
511C1-01220-0100-478DF2A .
When the computer is rebooted, WinPower software will be
shown as an icon with plug shape and green colour in the
system tray, near the clock.
4.3.8. Considerations
before
commissioning with load
connected.
Ŗ
It is recommended to charge the batteries for 2 hours
as minimum before using the UPS for first time. When
supplying voltage to the equipment, the battery charger will
automatically work.
Ŗ
(B1) equipments with extended back up time has a
battery charger with higher quality performances. It is
recommended to charge the batteries for 2 hours as min-
imum before using the UPS for first time.
Ŗ
Nevertheless, those equipments with extended back
up time and with no additional battery charger, it s rec-
ommended to charge the batteries of each battery module for
2 hours.
Ŗ
Although the equipment can work without charging the bat-
teries during the stated time without any problem, the risk of
a long blackout has to be valued during the first operating
hours and the available autonomy time in the UPS.
Ŗ
Do not start up the equipment and loads completely till
chapter 6 states it.
Thiele KG • V
orderer W
einberg 26 • D-71522 Backnang • T
el.:(07191)3560-0 • Fax.:(07191)3560-19 • info@thiele-electroni
c.de • www
.thiele-electronic.de
Thiele KG • V
orderer W
einberg 26 • D-71522 Backnang • T
el.:(07191)3560-0 • Fax.:(07191)3560-19 • info@thiele-electroni
c.de • www
.thiele-electronic.de
Vorderer Weinberg 26
• D-71522 Backnang •
Tel.:+49 (0)7191 3560-0 (Fax.:-19)
