background image

17

SALICRU

 

ˆ

Remove the beautiful front cover of the equipment and 
battery module, as it is described in section 4.2.4.1.

 

ˆ

Take the extensible cable with connector "H" of the bat-
tery module and connect it with the "G" connector of the 
equipment.

To connect it with other battery modules, there is the "J" 
connector. Take the extensible cable with "H" connector 
of the beside battery module and connect it to the "J" con-
nector of the previous one. Repeat the same steps for a 
high quantity of modules.

"A"

"A"

"B"

"C"

"D"

"E"

"F"

"H"

"J"

"G"

"K"

"K"

Fig. 7. 

Model in vertical -tower type- assembling with ex-
tended back up time (battery module).

 

ˆ

In the side of each front cover, there are the "K" trims as a 
notch to go the cables through it with the battery modules. 
Break the needed trims to pass the connection bus.

 

ˆ

Put the beautiful front cover back of the equipment and 
battery module, as it is stated in section  4.2.4.1.

4.2.4.5.  19" rack cabinet assembling.

Ŗ

All models can be installed in a 19" rack cabinet, attending 
the height of each one of them is 2 units.

Ŗ

Proceed as follows  (see figure 8):

 

ˆ

Fix both adaptor angles "A" of the equipment as rack, to 
its side by means of the supplied screws.

 

ˆ

Put a UPS in a rack cabinet, it is needed to have the side 
internal  rail  as  support  mode  "C".  In  lack  of  them  and 
under request, a rails can be supplied as a guide, to be 

Thiele KG • V

orderer W

einberg 26 • D-71522 Backnang • T

el.:(07191)3560-0 • Fax.:(07191)3560-19 • info@thiele-electroni

c.de • www

.thiele-electronic.de

Thiele KG • V

orderer W

einberg 26 • D-71522 Backnang • T

el.:(07191)3560-0 • Fax.:(07191)3560-19 • info@thiele-electroni

c.de • www

.thiele-electronic.de

Vorderer Weinberg 26

 • D-71522 Backnang • 

Tel.:+49 (0)7191 3560-0 (Fax.:-19)

Summary of Contents for SPS.1000.ADV RT

































Reviews: