pg. 14
5A
5A
5A
5A
5A
DESCRIPTION OF "ECOTHERM 3001 THERMOCOMFORT" CONTROLS
DESCRIPTION OF "ECOTHERM 3001 THERMOCOMFORT" CONTROLS
DESCRIPTION OF "ECOTHERM 3001 THERMOCOMFORT" CONTROLS
DESCRIPTION OF "ECOTHERM 3001 THERMOCOMFORT" CONTROLS
DESCRIPTION OF "ECOTHERM 3001 THERMOCOMFORT" CONTROLS
5A.1
5A.1
5A.1
5A.1
5A.1
DESCRIPTION OF CONTR
DESCRIPTION OF CONTR
DESCRIPTION OF CONTR
DESCRIPTION OF CONTR
DESCRIPTION OF CONTROL P
OL P
OL P
OL P
OL PANEL
ANEL
ANEL
ANEL
ANEL AND HEA
AND HEA
AND HEA
AND HEA
AND HEATER REAR P
TER REAR P
TER REAR P
TER REAR P
TER REAR PANEL
ANEL
ANEL
ANEL
ANEL
5A.1.1 DESCRIPTION OF CONTROL PANEL
There are two main control pushbuttons marked with the ventilation symbol (2) and the symbol of the flame (1).The flame pushbutton (1)
sets the power of the heater with 5 levels available which are activated as the 5 leds light up in sequence (10). The off cycle is activated
when all power leds are turned off. Key (2) controls the ventilation of the heater. The heater activates when the temperature exceeds 42
°C. The ventilation can be set up to 6 speed levels (9): when the heater is on the ventilation cannot be switched off .
5A.1.2 REAR PANEL
A description of the functions of the buttons and LEDs on the back panel of
the heater:
(11) Main switch 0-1
(12) Heater electrical power outlet 220-240V 50 Hz.
(13) Overtemperature thermostat button cap
In the event of overtemperature this safety thermostat stops the loading of
pellets. When it is activated LED 15 comes on.
To restart the heater you need to wait until it cools down, then verify the
cause for the overheating, remove the cause, unscrew the protective cap
and press the button (13) .
(14) Feed motor test indicator light When the pellet screw feeder is set
in motion the light must come on.
(15) Reset thermostat tripped indicator light. This LED comes on when
the reset thermostat is activated.
(16) Power outlet for additional chronothermostat connection
(additional chronothermostat not supplied)
(17) Power outlet for additional room temperature thermostat
connection
(additional room temperature thermostat not supplied)
All controls and indicators are presented here below :
(1) Insert on/off and flame adjustment button When you press this button the appliance (10) switches to Start / ON / OFF. Up to 5
leds (10) are activated when pressed repeatedly.
(2) Ventilation setting button Press this button to set the desired level of ventilation: up to a maximum of 6 speeds are available,
indicated by the lighting of the corresponding leds (9).
(3) (4) Auxiliary setting keys Keys (3) and (4) are operating keys necessary when on-off cycles are programmed, for operative levels,
clock setting, etc..
5) Programming Enable / Disable keys
(6) “MENU” selection button To access the main menu press the button marked with 6. Press button 6 repeatedly to scroll the
adjustment, setting and programming windows.
(7) Display
(8) Infrared sensor for remote control
(9) Ventilation level leds
(10) Combustion level leds
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
12
KEY
Room temperature
thermostat
Chronothermostat
- modem
Motor LED
Reset LED
Reset
LEGENDA
Termostato
ambiente
Cronotermostato -
modem
Spia Motor
Spia riarmo
Riarmo
