background image

14  |   Installing Independent Sensors

DeviceLink Connect

Installing Independent Sensors

Smart Sensor Assembly (RTD and Current Transducer)

PT100 (Temperature RTD) sensors and current transducers require the use of an intermediate connection cable called a Smart-
Cable. Each Smart-Cable connects to the DeviceLink Connect via one of the four available USB ports. The following 
information describes the connection and wire removal process for Smart-Cables.

Wire Insertion

1. The wires can be pushed in by hand. Place the wire fully 

into the circular Wire Hole. The wire should easily insert to 
a depth of about 7/16 of an inch.

2. Pull lightly on the wire to ensure that the wire is being 

retained by the terminal block.

Wire Removal

1. Insert the micro-screwdriver into the rectangular Insert/

Release slot for the wire that you want to remove. 
Inserting the micro-screwdriver into the slot requires 
some additional downward pressure to actually open the 
wire clamp that retains the conductor. You will notice that 
the tool will bottom out when initially inserted; then with a 
small amount of additional applied pressure, penetrate 
into the slot an additional 10%. This additional 
penetration will open a clamp allowing for the easy 
removal of the conductor.

Figure 16. Yellow: 2-wire CT sensor

Figure 17. Blue: 3-wire PT100 RTD sensor

Figure 18. Smart-Cable terminal block (RTD shown)

Insert/Release Slot

Wire Hole

CAUTION: 

If inserting stranded wire, ensure that 

all the strands are fully inserted into the hole and 
not allowed to float free. Loose strands could 
easily short to adjacent conductors.

CAUTION: 

The Insert/Release slot can be easily 

damaged by using too much downward force or 
tweaking of the micro-screwdriver.

Summary of Contents for DeviceLink Connect




































Reviews: