Thermo Scientific VARIOKLAV 25T Operating Manual Download Page 56

Page: 56 / 60

12 Troubleshooting

03/2007

DA0621_a/

Message in the
cycle display

Meaning Remedy

Error 17
Overheating

Heating system does not turn off.

Heating system relay defective or
program control error.

Contact after-sales
service.

Error 20
Microheating

Microheating system (heatable
temperature sensor) cannot regulate
water feed to jacket.

Microheating system defective.

Contact after-sales
service.

Error 22
No heater

Heating coils are defective, or
the heating system control is
defective.

Contact after-sales
service.

Error 23
Partial heater

One heating coil is defective.

Contact after-sales
service.

Err1

in the Chamber
field:

in the Media field:

Sensor broken

Chamber temperature sensor is
affected.

Flexible temperature sensor
(reference temperature sensor) is
affected

Have technician
replace sensor or
contact after-sales
service.

Err2

in the Chamber
field:

in the Media field:

Sensor shorted

Chamber temperature sensor

Flexible temperature sensor

12)2)2)

(reference temperature sensor).

Have technician
replace sensor or
contact after-sales
service.

Err3

in the Chamber
field:
in the Jacket field:
below the Jacket
field:

Pressure sensor defective

Pressure sensor in sterilizing
chamber
Pressure sensor in jacket

12)

Pressure sensor in seal

12)

Contact after-sales
service.

Table 5: Error codes and their meanings

12)

If present

Summary of Contents for VARIOKLAV 25T





























































Search results

Summary of Contents for VARIOKLAV 25T

Reviews:

Related manuals for VARIOKLAV 25T

Brands by name

Popular brands

Thermo Scientific VARIOKLAV 25T, Operating Manual

Search results

Summary of Contents for VARIOKLAV 25T

Reviews:

Related manuals for VARIOKLAV 25T

Brands by name

Popular brands