manualshive.com logo in svg

Thermo Scientific MIE ADR-1500, Instruction Manual

Share
Download
Thermo Scientific MIE ADR-1500 Instruction Manual Download Page 106

Maintenance and Service 

5-18

     MIE ADR-1500 Instruction Manual 

Thermo Fisher Scientific 

 

Use the following procedure to remove the optics enclosure assembly. 

1.

 

Turn the instrument OFF. Remove the AC plug from the bottom of 
the instrument. 

2.

 

Unfasten the two captive hardware and swing cover down on the 
power/com assembly. 

3.

 

Disconnect the battery cable from J6 or J8 from the power 
communication board. 

4.

 

Disconnect “LCD cable” from LCD. 

5.

 

Disconnect “Main board power cable” from communication board 
“J13”. 

6.

 

Disconnect “RH/Temp Cable” from communication board “Main BD 
J12” 

7.

 

Disconnect “RH/Temp BD cable” from communication board “J14”. 

8.

 

Disconnect “Com flex cable” from communication board “J16”. 

9.

 

Disconnect “pump cable” from communication board “PUMP IN J3”. 

10.

 

Disconnect “heater cable” form communication board “HEATER 
OUT J15”. 

11.

 

Use needle nose pliers and release the push connect fitting that is 
attached to the tubing on the small bypass filter. 

12.

 

Use needle nose pliers and release the push connect fitting that is 
attached to the large bypass filter. Move filter downwards to gain space. 

13.

 

Use needle nose pliers to release exhaust port tubing. 

14.

 

Use adjustable wrench to loosen inlet fitting. 

Optics Enclosure

Assembly Removal

Summary of Contents for MIE ADR-1500



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands