Thermo Scientific IonPac CG16 Product Manual Download Page 60 | Manualshive

Page: 60 / 67

background image

Product Manual for IonPac CS16

Page 58 of 65

6.7.1.

Poor Efficiency Using Capillary Columns

Incorrectly installed fittings on capillary tubing can increase void volumes, causing chromatograms with tailing peaks.

Figure 33

Tailing Peaks Caused by Incorrectly Installed

Capillary Tubing Fittings

When connecting a capillary tube fitting, make sure that the ferrule and fitting bolt are at least 2 mm (0.1 in) from the
end of the tubing before you insert the tubing into the port. Do not place the ferrule and fitting bolt flush with the end of
the tubing. Figure 33 illustrates the correct and incorrect placement of the ferrule and fitting bolt on the tubing.

Correc t

Incorrect

2 mm

Figure 34

Correct and Incorrect Ferrule and

Fitting Bolt Placement for Capillary Tubing Connections

Document No. 031747-05

© 2010 Dionex Corporation

December 2010

«
...
58
59
60
61
62
...
»

Summary of Contents for IonPac CG16




































































Reviews:

No comments

Related manuals for IonPac CG16

Brand: Daavlin Pages: 13

Brand: Daavlin Pages: 27

Brand: Bacharach Pages: 48

Brand: ECE Pages: 2

Brand: Ecco Pages: 5

Evolution Series

Brand: Bakare Pages: 38

Brand: XM Fitness Pages: 10

MET ONE 3400 Series

Brand: Hach Pages: 48

Brand: Major tech Pages: 12

Brand: PacBio Pages: 13

Brand: Pablo Pages: 4

Brand: PA Pages: 28

Brand: Radial Engineering Pages: 16

Brand: R&S Pages: 61

Brand: Yamaha Pages: 5

McDonnell & Miller PSE-800-M

Brand: Xylem Pages: 20

Brand: Tieline Pages: 359

Brand: BRAND Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands