Thermo Scientific IonPac CG16 Product Manual Download Page 11

Page: 11 / 67

Product Manual for IonPac CS16

Page 9 of 65

Separator Column Outlet

Separator Column

Separator Column Inlet

Precision Cut Tubing

Figure 2

Separator Column Only Installed in Column Cartridge

Locate the IC Cube Tubing Kit (P/N 072186) that is shipped with the IC Cube. The tubing kit includes the following
items:

Table 4

Contents of the IC Cube Tubing Kit (P/N 072186)

Part

Length /
Quantity

Part
Number

Used To Connect…

Precision cut 0.062-mm
(0.0025-in) ID PEEK tubing,
blue

65 mm
(2.56 in)

072188

50 mm guard column
outlet to 250 mm
separator column
inlet

Precision cut 0.062-mm
(0.0025-in) ID PEEK tubing,
blue, labeled
VALVE PORT 3

115 mm
(4.53 in)

072189

Guard column inlet to
injection valve

Precision cut 0.062-mm
(0.0025-in) ID PEEK
tubing, blue

75 mm
(2.93 in)

074603

35 mm guard column
outlet to 150 mm
separator column
inlet

Precision cut 0.062-mm
(0.0025-in) ID PEEK
tubing, blue, labeled
VALVE PORT 3

210 mm
(8.27 in)

072187 Separator

column

inlet to injection valve
(if a guard column is
not present)

0.25-mm (0.010-in) ID
PEEK tubing, black

610 mm
(24 in)

042690 EG

degas

cartridge

REGEN OUT to
waste (if an EG is not
present)

Fitting bolt, 10-32 hex
double-cone (smaller),
black

3 072949

Connect

precision

cut 0.062-mm
(0.0025-in) ID PEEK
tubing

Fitting bolt, 10-32
double-cone (larger),
black

1 043275

Connect

0.25-mm

(0.010-in) ID PEEK
tubing (black)

Ferrule fitting, 10-32
double-cone, tan

043276

Use with both sizes
of fitting bolts

Document No. 031747-05

December 2010

Summary of Contents for IonPac CG16




































































Search results

Summary of Contents for IonPac CG16

Reviews:

Related manuals for IonPac CG16

Brands by name

Popular brands

Thermo Scientific IonPac CG16, Product Manual

Search results

Summary of Contents for IonPac CG16

Reviews:

Related manuals for IonPac CG16

Brands by name

Popular brands