Thermo Scientific iCAP 7000 Series Manual Download Page 12 | Manualshive

Page: 12 / 72

background image

iCAP Customer Familiarisation Manual

Page 12 of 72

This document is part numbered 849940090071

Version 1.02

occurs during the liquid removal.

5.7 Position of the nebulizer in the spray chamber

Liquid should be delivered to the nebulizer using an identical plastic tubing connector but with
narrow bore tubing (0.50mm inner diameter). Push the white plastic tubing connector with the
attached narrow bore sample tubing into the rear of the nebulizer as far as possible without
exerting undue pressure.

The O-rings in the spray chamber should be inspected and replaced if any wear, or damage, is
visible. Using a twisting motion, insert the nebulizer into the spray chamber so that the nozzle is
level with the arc of the edge of the spray chamber. Small movements in and out are required to
optimize the measurement precision.

Modern designs of nebulizers have a collar to set the depth into the spray chamber. By inserting
the nebulizer into the spray chamber so that the collar is a tight fit the nebulizer will have the
insertion depth optimized and this will aid reproducibility of results.

Attach the quartz glass spray chamber adaptor to the spray chamber with the fitting clamp
provided.

Warning: The adaptor provided with the instrument is specially designed to prevent UV radiation
escaping from the torch box.

▲

«
...
10
11
12
13
14
...
»

Summary of Contents for iCAP 7000 Series









































































Reviews:

No comments

Related manuals for iCAP 7000 Series

Brand: Napoleon Pages: 2

Brand: Raytheon Pages: 62

Brand: 4iiii Pages: 36

Brand: 4iiii Pages: 34

Brand: 4EVAC Pages: 27

Brand: PANDROL Pages: 36

Brand: Rain-Flo Irrigation Pages: 16

Brand: JBL Pages: 38

Brand: JBSYSTEMS Light Pages: 32

Brand: JBM Pages: 12

Brand: U-Line Pages: 9

Green Machine H-3518

Brand: U-Line Pages: 3

Brand: Zimmer Pages: 54

Brand: Zimmer Pages: 4

Brand: Zimmer Biomet Pages: 23

Brand: Zimmer Pages: 16

Brand: Zimmer Pages: 2

Brand: Zimmer Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands