Thermo Scientific Evolution One Series User Manual Download

Page: 37 / 42

Evolution One Series Spectrophotometers

Using the Spectrophotometer

Thermo Scientific

Evolution One Series Spectrophotometer User Guide

Related Topics

Installing a Smart Accessory

Installing a Manual Accessory

Installing a Liquid Thermostatted Accessory

Using the Spectrophotometer

This section explains how to set up a Computer Control spectrophotometer.

Computer Control Instruments

Computer Control instruments must be connected to an external computer with the proper
software installed.

All instrument features can be run from the computer using our Insight Pro software.

Turning off a Computer Control Instrument

Maintenance

Setting up a Computer Control Instrument

To set up a Computer Control instrument

1. Connect the supplied USB cable to the Computer port on the back of the

spectrophotometer.

2. Connect the other end of the cable to the USB port on the back of the computer.

3. Turn on the spectrophotometer main power switch (on the back panel).

4. If the main power switch is already on, turn off the spectrophotometer main

power switch.

Wait for the system to initialize. This may take several minutes. The status light pipe
stops blinking when initialization is complete.

Contents

•

Computer Control Instruments

Note

If the instrument fails to initialize, the power indicator blinks rapidly. Contact us.

Summary of Contents for Evolution One Series











































Search results

Summary of Contents for Evolution One Series

Reviews:

Related manuals for Evolution One Series

Brands by name

Popular brands

Thermo Scientific Evolution One Series, User Manual

Search results

Summary of Contents for Evolution One Series

Reviews:

Related manuals for Evolution One Series

Brands by name

Popular brands